Traceable 5002CC -laboratorioajastimen käyttöopas

Jäljitettävä 5002CC-laboratorioajastin

HÄLYTYKSET
Each channel has a distinct electronic tone that sounds at the end of its timing period. Channel One has one repeating beep; Channel Two has two repeating beeps; and Channel Three has three repeating beeps. A channel’s tone will sound for 1 minute then shut off automatically to preserve battery life.

NÄYTÖN PUHDISTAMINEN NOLLAAN

Press and hold (approximately 2 seconds) the 1, 2, or 3 button to clear the display to zero for Channel One, Two, or Three respectively. If no channel is active, pressing and holding the 1, 2, or 3 button will shut off the unit entirely.

AJASTIMEN KÄYTTÖ

All three timing channels work essentially the same way, so once you understand how Channel One operates, Channels Two and Three will seem extra easy.

LASKURIAJAN ASETTAMINEN

1. Press the 1 button, digital display will then show all zeros. The symbol will be below the 1 button indicating Channel One is displayed.
2. Set the hours to be timed: Press the H button until the desired number of hours are displayed. For rapid advancement, press and hold button.
3. Set the minutes to be timed: Press the M button until the desired number of minutes are displayed. For rapid advancement, press and hold button.
4. Set the seconds to be timed: Press the S button until the desired number of seconds are displayed. For rapid advancement, press and hold button.
5. When the desired amount of time is showing on the digital display, simply press the 1 button to begin timing. You’ll know timing has begun when the seconds start counting down.
6. A single repeating electronic tone will sound at the end of the timing period and the symbol below the 1 button indicates status of the timing operation. (See “Channel Indicators” table).
7. To reset a channel to zero, to turn off a channel, or to turn off a channel while it is timing, simply press and hold down the appropriate channel (Channel One, Two or Three) for two seconds.

HUOMAA: The tone will continue to sound for 1 minute or until it is turned off. To turn off the tone, simply press the 1 button and release.

EXAMPLES
Channels Two and Three operate the same way as Channel One, except you press the 2 button for Channel Two or the 3 button for Channel Three in every instance you pressed the 1 button when timing in Channel One. Two examples annetaan.

Example 1
Time 1 hour, 20 minutes, and 30 seconds in Channel 2:

1. Paina 2-painiketta.
2. Press H button once to read “1”.
3. Press M button until display reads “20” minutes.
4. Press S button until display reads “30” seconds.
5. Press 2 button to start timing.
6. When the tone (two repeating beeps) sounds, press 2 button to turn it off.

Example 2
Time 9 hours, 15 minutes, and 10 seconds in Channel 3:

1. Paina 3-painiketta.
2. Press H button until display reads “9” hours.
3. Press M button until display reads “15” minutes.
4. Press S button until display reads “10” seconds.
5. Press 3 button to start timing.
6. When the tone (three repeating beeps) sounds, press 3 button to turn it off.

TEKNISET TIEDOT

• Näyttö: ¼* high, 5-digit  LCD
• Timing capacity: 9 hrs, 59 mins, 59 sec
• Resoluutio: 1 sec Accuracy: 0.001%
• Size, weight: 3 x 3 x 1⅜”, 4 oz

PIKA VIITE

• A-kanava näytetään
• B - Yksi kanava (1) -painike
• C - Kanavan kaksi (2) -painike
• D - Kanavan kolme (3) -painike
• E-kanava ei ajoitu tai näy
• F-kanava ajoittaa, mutta sitä ei näytetä
• G- Tunnit (H) -painike
• H- Minutes (M) button
• I – Seconds (S) button

Kanavan ilmaisimet
LCD indicators report the status of each channel.

AKUN VAIHTO

To replace the batteries, remove the back housing of the timer by giving the large screw on the back of the unit a half turn with a coin or screwdriver, then replace batteries as shown using two “AA” alkaline batteries. (Do not use regular or heavy-duty batteries. They do not have sufficient power to drive the unit.)

Kun olet asettanut paristot, varmista, että ajastimen näyttö toimii normaalisti. Ajastimen käytön aikana näytössä saattaa näkyä vilkkuvia segmenttejä. Jos näin käy, nollaa ajastin poistamalla paristot ja asettamalla ne takaisin paikalleen. Yhden paristosarjan pitäisi kestää 1–2 vuotta normaaleissa olosuhteissa. LCD-näyttö pysyy tyhjänä, kun paristot on vaihdettava.

TAKUU

TAKUU, HUOLTO TAI UUDELLEENKALIBROINTI
Takuuta, huoltoa tai uudelleenkalibrointia varten ota yhteyttä:

Jäljitettävät tuotteet 12554 Old Galveston Rd. Sviitti B230 Webster, Texas 77598 Yhdysvallat

• Puh. 281-482
• Faksi 281-482
• Sähköposti support@traceable.com
• www.jäljitettävä.com

Traceable® Products are ISO 9001:2015 Quality- Certified by DNV and ISO/EC 17025:2017 accredited as a Calibration Laboratory by A2LA.

Kissa. Nro 5002
Traceable® on Cole-Parmerin rekisteröity tavaramerkki.

©2020 Traceable® Products. 92-5002-00 Rev. 6 070825

UKK