HYPERCUBE HC15-SE Controller

Tekniset tiedot

	Hypercube-SE	Hypercube-SE
Dimensions (per side)	10.15” (258 mm)	15.16” (385 mm)
LEDejä yhteensä	216	336
LEDs Per Edge	18	28
Max Power Draw	10 W (2 A)	15 W (3 A)
Avg Power Draw	5 W (1 A)	7.5 W (1.5 A)
Paino	3.8 lb (1.7 kg)	8.2 lb (3.7 kg)
värit	~16 miljoonaa
LED -luokitus	50,000 XNUMX+ tuntia
Windows	Scratch-resistant mirrored acrylic
Kehys	ABS
Wifi-yhteys	2.4 GHz
System Voltage	5V
Standby Power Draw	<1W
Virtalähde	Accepts 100 – 240V, 50/60 Hz
Flux Capacitor Rating	3.14 Jigawatts

Turvallisuus ja hoito

• VAROITUS – Tulipalon vaara
  Keep the HyperCube out of direct sunlight. In rare cases, the mirrors can focus sunlight into a point that could cause burns or risk of fire.
• WARNING – Keep Dry
  Keep the HyperCube, and its controller and power supply away from excessive moisture. Water can damage the electronics and cause LED malfunction. Prolonged exposure can lower the lifetime of the LEDs. Our warranty does not cover water damage.
• WARNING – Electric Shock Risk
  Do not use or operate the device when wet for risk of electric shock.
• Hyper-Care
  The HyperCube is an art piece; while it is sturdy, it is not meant to be handled excessively. Be extremely careful with the mirrors. When cleaning the mirror panels, use only a microfiber cloth and, if needed, lightly soapy water. Clean very gently, without applying much pressure, to prevent damage to the mirrored panels.

Aloitus

What’s in the box?! 

• HyperCube
• Ohjauslaatikko
• Virtalähde

Virran kytkeminen päälle 

1. Plug the power supply into an outlet (accepts outlet voltage from 100-240V) and plug the USB cord into the power supply. You may also use any standard cell phone charging block (5V) with your own USB-C cord.
2. Connect the HyperCube cable to the control box. Note the orientation. To unplug, press the tab underneath.
3. Plug the USB-C connector into the front of the control box.
   The button on the control box will turn blue.
4. Olkoon valoa!

Toiminta

The HyperCube features 3 modes: 

• Kaleidoscopic: dynamic, fast, and colorful patterns. This is the default mode (40 patterns)
• Meditative: calm, classy and slowed down patterns to help you relax (24 patterns)
• Ääneen reagoiva: dance and entrance, with specially designed patterns that respond to the beat. A microphone is located inside the control box (31 patterns)
• Each mode is essentially a playlist of unique patterns. By default, a pattern plays for 60 seconds before switching. New colors are randomly generated every 10 seconds, for near-infinite variety! This behavior can be fully customized in the app. The patterns and modes can be controlled with the button on the control box.

Painike

The Hyperspace App 

Hyperspace Lighting
Download the “Hyperspace Lighting” app to fully control and customize your HyperCube!

Asennus

The setup process will connect your HyperCube to your home WiFi network for convenient smartphone control. (NOTE: the HyperCube only connects to 2.4 GHz networks)

1. Make sure the cube is not in sound reactive mode.
2. Open the app and press the “+” icon in the top right corner of the main menu
3.  Press “Add New Hyper-Device”
4. Enter your home WiFi credentials and press “Connect!”. All fields are case sensitive. Your phone must be connected to this verkkoonHuomautus: if the connection fails, press “Can’t Connect?” at the bottom of the screen and follow the instructions.
5. Accept any permissions and allow your phone to connect to the HyperCube WiFi network channel
6. Wait for the connection process to finish. This could take up to one minute
7. You may go back at any time to re-enter your WiFi credentials or restart the process. Multiple attempts may help in case of failure
8.  You’re done – press “My HyperCube” to pilot the controls!Ongelmia yhdistämisessä? 
9. Refresh: If the connection process finished but the cube isn’t showing up, refresh the device list by swiping down anywhere on the screen
10. Power the cube off and on (fully unplug), then reset the cube’s WiFi by holding the button on the control box for 10s (until the LEDs in the cube flash red then green).
11. Repeat steps 1-7. OR, in step 4 press “Can’t Connect?” at the bottom of the screen and follow the instructions.
12.  Alternatively: Press “Temporary Connect” on the “+” menu, “Config” in the top right of the device UI, then “WiFi Setup” at the top of the screen. Enter your WiFi credentials, then go back to the home screen of the app and refresh (swipe down).

Liitäntävinkkejä

• Ensure the cube is near your router for initial connection. It can be moved further after setup.
• Ensure you are connecting to a 2.4 GHz WiFi network, and your phone is already connected to this WiFi.
• Double check your WiFi name and password (both are case sensitive).
• Try again, sometimes multiple attempts are needed. Reset the cube’s WiFi and power cycle after each attempt.

Lost Connection?
If you’ve successfully connected before but lost connection:

1. Power cycle by fully unplugging it then plugging it back in.
2. Restart the app and refresh the device list by swiping down. Refresh a few times and wait up to a minute.
3.  If the device still does not connect, try steps 1-2 again, or reset the device and reconnect, by following the steps on the previous page (hold the button for 10s to reset WiFi).

Not at home?
If you’re out and about without a WiFi connection, you can still connect to the HyperCube’s internal WiFi hotspot. Press the “+” icon on the main menu and select “Temporary Connect” to access the controls! This will leave you connected to the HyperCube WiFi channel.

Control via PC, without the app
If you don’t have an Android/iOS smart phone, you can still connect to and control your HyperCube! All you need is an internet browser on your PC or phone. If you have already connected the cube with your phone, simply skip to step 5.

1. On your phone, connect to the “HyperCube” WiFi network. Password: hyperspace
2. A new window will appear (or a prompt will appear asking you to log in. Press this). Enter your home WiFi network information. This procedure will connect the HyperCube to your home network.
3.  Access your router settings. Typically, this can be done by entering the router IP address in a browser. Most use an address of 192.168.1.1, but you may need to confirm with your router’s manual.
4.  Find the list of connected devices and copy the Hypercube’s IP address (also in-app, after setup).
5. Enter the HyperCube IP address in any browser and you will be taken to the controls!

Connecting via E1.31
The HyperCube also supports pixel mapping via sACN/E1.31 protocol. Various third-party software can be used to control the LEDs, such as xLights and MadMapper. This feature is experimental, not guaranteed to work smoothly, and is recommended only for users with pixel mapping experience. The setup process differs for all software. In general, you will need your Hypercube’s IP address, shown on the main device list page:

You will also need the following pixel information: Hypercube: 288 total pixels (WS8211/WS2812) Hypercube: 480 total pixels (WS8211/WS2812)

The total pixels are split across 2 separate LED tracks, each with half the total pixels (i.e. 2 universes with 432/840 channels each for HC10/HC15).

Käyttö

Patterns Menu (default) 

Värit-valikko 

More Controls Menu 

Suosikit-valikko
Save your favorite patterns for easy playback! All color, speed, intensity, and symmetry customizations are also saved.

Asetukset-valikko

Vianetsintä

Trouble connecting to the app?
Try the alternative connection process here.

1. Reset the cube’s WiFi by holding the button on the control box for 10s (until the LEDs in the cube flash red then green).
2.  Connect to the “HyperCube” WiFi network with your phone. If prompted, stay connected without internet access.
3. Avaa a web browser and navigate to hyperspace.local
4. Press “config” in the top right, then “WiFi Setup”. Enter your home WiFi credentials (case sensitive) and save.
5. Connect back to your home WiFi, open the Hyperspace app, then swipe down to refresh the device list. The list refreshes every 15s, you may need to wait or manually refresh multiple times.
6. Your HyperCube should now appear on the device list and be connected!
7.  If all else fails, the WiFi connection can be reset by holding the button on the control box for 10 seconds. After, re-do the initial setup procedure (“+”  “Add New Hyper Device  Connect!).

Want to connect an additional device to the cube?
You can control one HyperCube from multiple devices. If you have already gone through the initial setup process once, on your new device simply swipe down on the main device list page to refresh. You may need to refresh multiple times, and wait up 1-2 minutes. All hyper-devices connected to the WiFi network will be added after some time.

Sound reactivity issues?
The HyperCube automatically adjusts to a wide range of volume levels, but still requires a moderate volume and/or distance-to-source to respond best. The microphone is located in the control box; for optimal performance, keep the sound source 3 – 10 ft away.

• If the HyperCube appears too sensitive to ambient noise (patterns trigger with no sound) or won’t respond, the microphone sensitivity can be adjusted. Go to settings > sound reactivity and adjust the sensitivity value. Higher values will allow the mic to pick up softer sounds, but may trigger the lights on ambient/electrical noise.

Note that if music volume is extremely loud (and close to the control box), the sound response may be poor.

Takuu

The Hyperspace Lighting Company, LLC offers a 1-year limited warranty on each HyperCube. We guarantee that each product purchased will arrive in working condition, without damage, and will be free from defects in electrical operation for a period of one (1) year from the date of delivery. Please contact us at the email address below if you have any issues, we’re here to help!

The full detailed warranty description can be found online at https://hyperspacelight.com/pages/1-year-limited-warranty

Ota yhteyttä
Questions, comments, concerns? Lost in hyperspace and can’t find your way out? Email us at: hello@hyperspacelight.com.

CE Registration: HK2506203256E

 

Tämä laite on FCC-sääntöjen osan 15 mukainen. Toiminta on kahden seuraavan ehdon alaista:

1. Tämä laite ei saa aiheuttaa haitallisia häiriöitä ja
2.  Tämän laitteen on hyväksyttävä kaikki vastaanotetut häiriöt, mukaan lukien häiriöt, jotka voivat aiheuttaa ei-toivottua toimintaa.

Muutokset, joita vaatimustenmukaisuudesta vastaava osapuoli ei ole nimenomaisesti hyväksynyt, voivat mitätöidä käyttäjän oikeuden käyttää laitetta. Tämä laite on testattu ja sen on todettu noudattavan luokan B digitaalisille laitteille asetettuja rajoituksia FCC-sääntöjen osan 15 mukaisesti. Nämä rajoitukset on suunniteltu tarjoamaan kohtuullinen suoja haitallisia häiriöitä vastaan ​​kotiasennuksessa. Tämä laite tuottaa ja voi säteillä radiotaajuista energiaa, ja jos sitä ei asenneta ja käytetä ohjeiden mukaisesti, se voi aiheuttaa haitallisia häiriöitä radioviestintään. Ei kuitenkaan ole takeita siitä, ettei häiriöitä tapahdu tietyssä asennuksessa. Jos tämä laite aiheuttaa haitallisia häiriöitä radio- tai televisiovastaanottoon, mikä voidaan määrittää sammuttamalla ja käynnistämällä laite, käyttäjää kehotetaan yrittämään korjata häiriöt yhdellä tai useammalla seuraavista toimenpiteistä:

• Suuntaa tai siirrä vastaanottoantenni uudelleen.
• Lisää laitteen ja vastaanottimen välistä etäisyyttä.
• Liitä laite pistorasiaan, joka on eri piirissä kuin se, johon vastaanotin on kytketty.
• Pyydä apua jälleenmyyjältä tai kokeneelta radio-/TV-teknikkolta.ct.

Tämä laite noudattaa FCC:n RF-säteilyaltistusrajoja, jotka on asetettu hallitsemattomalle ympäristölle. Tämä laite tulee asentaa ja sitä tulee käyttää vähintään 20 cm:n etäisyydellä jäähdyttimen ja minkä tahansa kehon osan välillä.

Usein kysytyt kysymykset

Can I leave the HyperCube on for extended periods?

It is recommended to turn off the HyperCube when not in use to conserve energy and prolong the lifespan of the LEDs.

How do I clean the HyperCube mirrors?

Use a microfiber cloth with light soapy water to gently clean the mirror panels. Avoid applying excessive pressure to prevent damage.

Asiakirjat / Resurssit

HYPERCUBE HC15-SE Controller [pdfKäyttöopas HC15-SE, HC15-SE Controller, Controller

Viitteet

• Käyttöopas