1. Johdanto
This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of the Richmat HJA63 Foot Actuator. This actuator is designed as a replacement component for adjustable bed bases, facilitating the movement of the foot section.
2. Turvallisuustiedot
- Always disconnect power to the adjustable bed base before attempting any installation, maintenance, or repair.
- Varmista, että kaikki liitännät ovat kunnossa ja oikein ennen virran kytkemistä uudelleen.
- Do not attempt to modify the actuator or its components.
- Pidä kädet ja löysät vaatteet poissa liikkuvista osista käytön aikana.
- This product is designed for specific adjustable bed base applications. Do not use for unintended purposes.
- Refer to the original bed base manufacturer's manual for additional safety guidelines.
3. Pakkauksen sisältö
Varmista avatessasi pakkauksen, että kaikki osat ovat mukana ja ehjät:
- 1 x Richmat HJA63 Foot Actuator
Kuva 3.1: Yliview of the Richmat HJA63 Foot Actuator. This image shows the complete actuator unit, including the motor housing, linear shaft, and mounting points.
4. Asennus ja asennus
Installation of the Richmat HJA63 Foot Actuator typically involves replacing an existing actuator. Follow these general steps:
- Katkaise virta: Unplug the adjustable bed base from the wall outlet to ensure no power is supplied during installation.
- Locate Existing Actuator: Identify the foot actuator on your adjustable bed base. It is usually connected to the frame and the moving foot section.
- Irrota johdot: Carefully disconnect the electrical cable from the control box or power supply unit. Note the type of connector.
- Remove Mounting Pins/Bolts: Remove the pins or bolts that secure the actuator to the bed frame at both ends. Keep these fasteners for reinstallation.
- Irrota vanha toimilaite: Carefully slide out the old actuator.
- Asenna uusi toimilaite: Position the new Richmat HJA63 actuator in the same location. Align the mounting holes.
- Secure Mounting Pins/Bolts: Reinsert and secure the mounting pins or bolts at both ends of the actuator. Ensure they are tight but allow for smooth pivot.
- Kytke johdotus: Connect the electrical cable of the new actuator to the control box or power supply unit. Ensure the 5-pin connector is fully seated.
Kuva 4.1: Richmat HJA63 Actuator showing the 5-pin electrical connector. This connector is used to interface with the bed base's control system.
Tärkeää: Before restoring power, double-check all connections and ensure there are no obstructions around the actuator's path of motion.
5. Käyttöohjeet
Once the Richmat HJA63 Foot Actuator is correctly installed and connected, its operation is controlled by the adjustable bed base's remote or control panel. The actuator extends and retracts to raise and lower the foot section of the bed.
- Virta päälle: Plug the adjustable bed base back into the wall outlet.
- Testauksen toiminnallisuus: Use the bed's remote control to slowly raise and lower the foot section. Observe the actuator's movement to ensure it operates smoothly and without obstruction.
- Käyttömäärä: The actuator has a duty cycle of 10%, maximum 2 minutes ON / 18 minutes OFF. This means it should not be operated continuously for more than 2 minutes at a time, and requires an 18-minute rest period to prevent overheating.
6. Huolto
The Richmat HJA63 Foot Actuator is designed for low maintenance. However, periodic checks can help ensure its longevity:
- Puhdistus: Wipe the exterior of the actuator with a dry or slightly damp kangas. Älä käytä voimakkaita kemikaaleja tai hankaavia puhdistusaineita.
- Tarkastus: Periodically inspect the mounting points and electrical connections for any signs of wear, looseness, or damage.
- Voitelu: The internal components are pre-lubricated and do not require additional lubrication.
7. Vianmääritys
If you experience issues with your Richmat HJA63 Foot Actuator, consider the following common troubleshooting steps:
| Ongelma | Mahdollinen syy | Ratkaisu |
|---|---|---|
| Toimilaite ei liiku. | No power; Loose connection; Overload; Remote issue. | Check if bed base is plugged in. Ensure all cables are securely connected. Reduce load on bed. Test with another remote if possible, or check remote batteries. |
| Actuator moves slowly or intermittently. | Alhainen tilavuustage; Overheating; Obstruction. | Ensure stable power supply. Allow actuator to cool down (observe duty cycle). Check for any objects obstructing the actuator's movement. |
| Epätavallinen ääni toimilaitteesta. | Loose mounting; Internal issue. | Check and tighten mounting pins/bolts. If noise persists and is significant, the actuator may require replacement. |
Jos vianmääritysohjeet eivät ratkaise ongelmaa, ota yhteyttä asiakastukeen.
8. Tekniset tiedot
Technical specifications for the Richmat HJA63 Foot Actuator:
Kuva 8.1: Product label detailing the specifications of the Richmat HJA63 Actuator. Key information includes model number, voltage, current, load capacity, and duty cycle.
| Ominaisuus | Yksityiskohta |
|---|---|
| Malli | HJA63 |
| Rated Voltage | DC 24V |
| Suurin virta | 3.5A max |
| Max Load (Push) | 6000N |
| Aivohalvaus | 80/200 mm |
| Käyttömäärä | 10%, Max 2min ON / 18min OFF |
| IP-luokitus | IP20 |
| Liittimen tyyppi | 5-nastainen DIN |
9. Takuu ja tuki
For warranty information or technical support regarding your Richmat HJA63 Foot Actuator, please refer to the documentation provided with your adjustable bed base or contact the manufacturer/seller directly. Keep your purchase receipt as proof of purchase.
For general inquiries or further assistance, please visit the product's listing page or contact the seller through the platform where the purchase was made.
