Fluke 1507 Digitaalinen megaohmimittari Eristysresistanssitesteri Käyttöohje

1. Johdanto

The Fluke 1507 Digital Megohmmeter Insulation Resistance Tester is a robust and reliable instrument designed for comprehensive insulation testing in industrial and electrical environments. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Fluke 1507 tester.

Key features include multiple insulation test voltages, automatic calculation of Polarization Index (PI) and Dielectric Absorption Ratio (DAR), a Compare (Pass/Fail) function for repetitive testing, and live circuit detection for enhanced safety.

2. Turvallisuustiedot

WARNING: Always read and understand all safety information before operating the Fluke 1507 tester. Failure to do so may result in serious injury or death.

• Live-piirin tunnistus: The tester is equipped with live circuit detection, which prevents insulation tests if a voltage greater than 30 Volts is detected. This feature is crucial for user protection.
• Auto-Discharge: The 1507 provides auto-discharge of capacitive voltage for added user protection after testing.
• Mittausluokka: This instrument complies with ANSI/ISA 82.02.01 (61010-1) 2004, CAN/CSA-C22.2 No. 61010-1-04, and IEC/EN 61010-1 2nd edition for Measurement Category IV 600 V (CAT IV). Always use the tester within its specified measurement category.
• Oikea käyttö: Use only the test leads and accessories supplied or approved by Fluke. Inspect test leads for damage before each use.
• Ympäristöolosuhteet: Do not use the tester in wet or explosive environments. Ensure the operating area is dry and well-ventilated.

3. Komponentit ja mukana toimitetut lisävarusteet

The Fluke 1507 Insulation Resistance Tester package typically includes the following items:

• Fluke 1507 Insulation Resistance Tester Unit
• TL224 Test Leads
• TP74 Test Probes
• Alligaattorin leikkeet
• Kotelo
• Kauko-anturi
• Four AA Batteries (pre-installed or included separately)

4. Asennus

4.1. Akun asennus

The Fluke 1507 requires four AA alkaline batteries for operation. These are typically included with the unit. To install or replace batteries:

1. Varmista, että testeri on sammutettu.
2. Paikanna paristolokero laitteen takaosasta.
3. Avaa paristolokeron kansi ruuvimeisselillä.
4. Insert the four AA batteries, observing the correct polarity as indicated inside the compartment.
5. Aseta paristolokeron kansi takaisin paikalleen ja kiinnitä se ruuvilla.

4.2. Testijohtojen liittäminen

Connect the test leads to the appropriate input jacks on the tester. For insulation resistance measurements, use the 'V Ω' and 'COM' jacks. Ensure connections are secure before proceeding with any tests.

5. Käyttöohjeet

5.1. Virta päälle / pois

To power on the Fluke 1507, rotate the rotary switch from the 'OFF' position to any desired measurement function. The large, backlit display will illuminate. To power off, rotate the switch back to 'OFF'. The unit also features an auto-power off function to conserve battery life.

5.2. Testimäärän valitseminentages

The Fluke 1507 offers multiple insulation test voltages. Rotate the main rotary switch to the 'INSULATION' section. Then, use the dedicated voltage selection buttons (50 V, 100 V, 250 V, 500 V, 1000 V) to choose the appropriate test voltage hakemuksellesi.

5.3. Performing Insulation Tests

Once the desired test voltage is selected and test leads are connected to the circuit under test:

1. Paina ja pidä painettuna TESTATA button to initiate the insulation test. The display will show the measured insulation resistance.
2. For hands-free operation during repetitive tests, utilize the remote test probe.
3. The live circuit detection feature will prevent a test if voltage exceeds 30V, indicated by a warning on the display.

5.4. Compare (Pass/Fail) Function

The Compare (Pass/Fail) function simplifies repetitive testing by allowing you to set a pass/fail threshold. Refer to the on-screen prompts and the user interface for setting this function. The tester will then indicate whether the measured resistance meets the predefined criteria.

5.5. Polarisaatioindeksi (PI) ja dielektrinen absorptiosuhde (DAR)

The Fluke 1507 automatically calculates Polarization Index (PI) and Dielectric Absorption Ratio (DAR), saving time and ensuring accurate assessment of insulation condition. These functions are typically accessed via dedicated buttons on the front panel.

6. Huolto

6.1. Puhdistus

To clean the exterior of the tester, use a damp cloth and a mild detergent. Do not use abrasive cleaners or solvents. Ensure the unit is completely dry before storage or next use.

6.2. Pariston vaihto

Replace batteries when the low battery indicator appears on the display. Refer to Section 4.1 for detailed battery installation instructions. Always use fresh alkaline batteries.

6.3. Kalibrointi

For optimal performance and accuracy, periodic calibration by an authorized service center is recommended. Refer to your warranty information or contact Fluke support for calibration schedules and services.

7. Vianmääritys

This section provides solutions to common issues you might encounter with your Fluke 1507 tester.

8. Tekniset tiedot

9. Takuu ja tuki

9.1. Takuutiedot

The Fluke 1507 Digital Megohmmeter Insulation Resistance Tester comes with a 1-Year warranty. Please retain your proof of purchase for warranty claims. The warranty covers defects in materials and workmanship under normal use.

9.2. Asiakastuki

For technical assistance, service, or to inquire about calibration services, please visit the official Fluke website or contact their customer support. You can also refer to the comprehensive User Manual (PDF) available online for more detailed information:

• Lataa käyttöohje (PDF)