IDEC ASLW212620S Illuminated 22mm Selector Switch User Manual

1. Tuote ohiview

This manual provides essential information for the safe and effective installation, operation, and maintenance of the IDEC ASLW212620S Illuminated 22mm Selector Switch. This device is designed for industrial control applications, offering a clear visual indication of its operational state through illumination.

Kuva 1: IDEC ASLW212620S Illuminated 22mm Selector Switch. This image displays the complete assembly of the selector switch, including the illuminated actuator, mounting base, and contact blocks. The blue translucent handle indicates its illuminated feature.

Tärkeimmät ominaisuudet:

• 22mm mounting diameter for standard panel cutouts.
• Illuminated actuator for clear status indication.
• Two-position selector switch functionality.
• Panel mount design.
• IP54 International Protection Rating, offering protection against dust and splashing water.

2. Turvallisuustiedot

Read and understand all instructions before installing, operating, or maintaining this product. Failure to follow these instructions may result in serious injury or property damage.

• Sähköinen vaara: Ensure all power is disconnected before performing any installation or maintenance. Only qualified personnel should perform electrical work.
• Oikea käyttö: Use this switch only for its intended purpose in industrial control circuits. Do not exceed specified voltage ja nykyiset arvosanat.
• Ympäristöolosuhteet: Do not expose the switch to conditions outside its specified operating temperature, humidity, or IP rating.
• Tarkastus: Regularly inspect the switch for any signs of damage, wear, or loose connections. Replace damaged components immediately.

3. Asennus ja asennus

Proper installation is crucial for the reliable operation of the IDEC ASLW212620S selector switch.

3.1 Paneeliasennus

1. Ensure the control panel has a 22mm diameter cutout for the switch.
2. Insert the switch actuator assembly through the front of the panel cutout.
3. Secure the switch to the panel using the provided mounting nut and washer on the rear side of the panel. Tighten securely but do not overtighten.
4. Attach the contact block(s) and lamp holder (if separate) to the rear of the switch assembly, ensuring they are correctly oriented and locked into place.

3.2 Johdotus

Refer to the wiring diagram provided with your specific contact block and lamp holder for detailed connection instructions. General guidelines are as follows:

• Ensure all power is off before wiring.
• Connect control circuit wires to the appropriate terminals on the contact blocks.
• Connect power for the illumination lamp l:lleamp holder terminals, observing correct polarity if applicable.
• Verify all connections are secure and free from shorts.

4. Käyttöohjeet

The IDEC ASLW212620S is a two-position selector switch. Its operation is straightforward:

• Position Selection: Rotate the switch actuator to select between the two available positions. Each position corresponds to a specific state of the connected control circuit.
• Valaistus: Integroitu lamp will illuminate when power is supplied to its terminals, providing a visual indication of the switch's status or the circuit's condition, depending on how it is wired.

5. Huolto

Regular maintenance helps ensure the longevity and reliable performance of your selector switch.

• Puhdistus: Puhdista kytkimen ulkopinta pehmeällä,amp cloth. Do not use abrasive cleaners or solvents, as these can damage the plastic components or markings.
• Tarkastus: Periodically check for loose mounting nuts, damaged wiring, or signs of corrosion on terminals. Ensure the actuator rotates smoothly between positions.
• Lamp Korvaus: Jos valaistus lamp fails, replace it with a lamp samasta tilavuudestatage and type specified by IDEC for this model. Ensure power is disconnected before replacing the lamp.

6. Vianmääritys

If you encounter issues with your IDEC ASLW212620S switch, consider the following common problems and solutions:

• Switch Not Actuating Circuit:
  • Check wiring connections to the contact blocks.
  • Verify the contact block is correctly attached and functioning.
  • Ensure the switch actuator is fully rotated to the desired position.
• Valaistus ei toimi:
  • Check power supply to the lamp pidin.
  • Tarkista johdotusliitännät l:äänamp pidin.
  • Tarkista lamp for damage or burnout; replace if necessary.
  • Varmista, että lamp holder is correctly installed.
• Stiff or Loose Actuator:
  • Check for foreign objects obstructing movement.
  • Ensure the mounting nut is not overtightened or too loose.
  • If the issue persists, the switch mechanism may be damaged and require replacement.

7. Tekniset tiedot

8. Takuu ja tuki

IDEC products are manufactured to high-quality standards. For specific warranty information, please refer to the documentation provided with your purchase or visit the official IDEC website. For technical support or further assistance, please contact IDEC customer service.

IDEC Corporation Contact Information:
(Please refer to the official IDEC website for the most current contact details and regional support information.)