Minoston Z-Wave -pistorasian (MP21Z) käyttöohje

Johdanto

This manual provides detailed instructions for the Minoston Z-Wave Outlet Mini Plug-in Socket (MP21Z). This device allows you to wirelessly control lamps and small appliances, integrate them into your Z-Wave smart home system, and extend your Z-Wave network range.

Tuote loppuview

Tärkeimmät ominaisuudet

• 800 Series Z-Wave Chip: Enhanced signal coverage, faster communication, and improved reliability.
• Z-Wave Plus Long Range (LR) Support: Extends wireless coverage up to 1300ft with compatible hubs.
• S2 Authenticated Security: Provides advanced security for your smart home network.
• SmartStart for Effortless Pairing: Simplifies the inclusion process with compatible Z-Wave hubs.
• Langaton ohjaus: Manage connected devices remotely via your Z-Wave hub and mobile application.
• Built-in Repeater: Acts as a signal repeater to strengthen your Z-Wave mesh network.
• Ajastin- ja aikataulutoiminnot: Automate device operation to save energy and enhance convenience.
• Kompakti muotoilu: Mini size ensures it does not block adjacent outlets.
• Suuri kapasiteetti: Supports loads up to 15A, 125 VAC.

Pakkauksen sisältö

• Minoston Z-Wave Outlet Mini Plug-in Socket (MP21Z) x 2
• Käyttöohje x 1

Tuotekaavio

This diagram illustrates the key components of the Minoston Z-Wave Mini Plug-in Socket.

Kuva: Edessä view of the Minoston Z-Wave Mini Plug-in Socket, highlighting its compact design and indicating its capabilities for scheduling, signal repeating, remote control, and manual on/off operation.

Kuva: Sivu view of the Minoston Z-Wave Mini Plug-in Socket, showing its dimensions (1.14 inches depth, 1.89 inches height) and the location of the program button.

• Ohjelmapainike: Used for manual ON/OFF control, Z-Wave inclusion/exclusion, and factory reset.
• Z-Wave Controlled Outlet: Standard 3-prong outlet for connecting appliances.

Turvallisuustiedot

Please read and understand all safety precautions before installation and use. Failure to follow these instructions may result in fire, electrical shock, or injury.

• Vain sisäkäyttöön: This device is designed for indoor use in dry locations. Do not expose to rain, moisture, or extreme temperatures.
• Sähköinen luokitus: Do not exceed the maximum load of 15A, 125 VAC (1875W). Overloading the device can cause overheating and fire.
• Maadoitus: Ensure the device is plugged into a properly grounded 3-prong outlet.
• Laitteen yhteensopivuus: Only connect appliances that are within the specified electrical rating. Do not use with medical or life-support equipment.
• Puhdistus: Katkaise virta ennen puhdistamista. Käytä vain kuivaa liinaa.
• purkaminen: Älä yritä purkaa tai korjata laitetta. Jätä kaikki huoltotyöt pätevän henkilöstön tehtäväksi.

Asennus ja asennus

The Minoston Z-Wave Outlet Mini Plug-in Socket requires a Z-Wave certified hub (sold separately) for smart control and automation. It is compatible with most Z-Wave hubs, including SmartThings, Vera, Wink, Fibaro, HomeSeer, Ring, 2GIG, and Hubitat.

Z-Wave Network Inclusion (Pairing)

There are two primary methods to add your Minoston Z-Wave Mini Plug to your Z-Wave network:

Image: Step-by-step guide for Z-Wave inclusion, illustrating both QR code scanning and manual pairing methods with a Z-Wave hub.

Method 1: SmartStart Inclusion (Recommended for 800 Series Hubs)

1. Ensure your Z-Wave hub supports SmartStart.
2. Open your Z-Wave hub's mobile application and select the option to add a new device (often found under "Add Device" or "SmartStart").
3. Scan the QR Code located on the product packaging or on the back of the device.
4. Plug the Minoston Z-Wave Mini Plug into a wall outlet. The device will automatically begin the inclusion process.
5. The device should appear in your hub's device list once successfully added.

Method 2: Manual Inclusion (Traditional Pairing)

1. Plug the Minoston Z-Wave Mini Plug into a wall outlet near your Z-Wave hub.
2. Put your Z-Wave hub into inclusion (pairing) mode. Refer to your hub's instruction manual for specific steps.
3. Press the program button on the Minoston Mini Plug kolme kertaa nopeasti. The LED indicator will flash to confirm it's attempting to pair.
4. Once successfully paired, the LED indicator will stop flashing and remain solid (or turn off, depending on the hub's configuration).
5. The device should appear in your hub's device list.

Z-Wave Network Exclusion (Removing)

To remove the Minoston Z-Wave Mini Plug from your Z-Wave network:

1. Plug the Minoston Z-Wave Mini Plug into a wall outlet.
2. Put your Z-Wave hub into exclusion (removal) mode. Refer to your hub's instruction manual for specific steps.
3. Press the program button on the Minoston Mini Plug kolme kertaa nopeasti. The LED indicator will flash to confirm it's attempting to exclude.
4. Once successfully excluded, the LED indicator will stop flashing.
5. The device will be removed from your hub's device list.

Tehdasasetusten palautus

A factory reset will restore the device to its default settings and remove it from any Z-Wave network. Only perform a factory reset when the primary controller is missing or inoperable.

1. Press and hold the program button for approximately 20 seconds.
2. The LED indicator will flash rapidly, then turn off, indicating a successful reset.

Käyttöohjeet

Manuaalinen ohjaus

The program button on the side of the Minoston Z-Wave Mini Plug allows for manual control of the connected appliance.

• Paina painiketta kerran: Toggles the connected appliance ON or OFF.

Langaton hallinta

Once successfully paired with your Z-Wave hub, you can control the Minoston Z-Wave Mini Plug wirelessly.

• Via Z-Wave Hub Application: Use your hub's mobile application to remotely turn the connected appliance ON or OFF from anywhere.
• Ääniohjaus: If your Z-Wave hub is integrated with voice assistants like Alexa or Google Assistant, you can use voice commands to control the plug (e.g., "Alexa, turn on the Christmas tree").

Image: A coffee maker connected to the Minoston Z-Wave Mini Plug, demonstrating its use for scheduled operation. The plug is shown in the OFF state, with a scheduled ON time of 6:35 AM.

Aikataulutus ja kohtaukset

Leverage your Z-Wave hub's capabilities to create schedules and scenes for automated control.

• Aikataulut: Set specific times for the plug to turn ON or OFF daily or weekly. This is useful for lights, coffee makers, or other routine appliances.
• Kohtaukset: Combine the Minoston Mini Plug with other Z-Wave devices to create custom scenes (e.g., a "Good Morning" scene that turns on your bedroom lamp and coffee maker).

Lisäominaisuudet

Z-Wave Repeater Functionality

The Minoston Z-Wave Mini Plug acts as a Z-Wave signal repeater. This means it re-transmits Z-Wave commands from your hub to other Z-Wave devices, extending the overall range and reliability of your Z-Wave mesh network. Place these plugs strategically to improve signal strength for devices further away from your hub.

Z-Wave Plus Long Range (LR)

This device supports Z-Wave Plus Long Range technology, offering significantly extended wireless range (up to 1300ft) when used with a compatible Z-Wave LR hub. This is particularly beneficial for larger homes or outdoor Z-Wave applications.

S2 Security and SmartStart

The 800 series Z-Wave chip incorporates S2 Authenticated Security, providing a higher level of encryption and protection against unauthorized access. SmartStart simplifies the pairing process by allowing devices to be added to the network by scanning a QR code, eliminating the need for manual button presses during initial setup.

Vianetsintä

Laite ei vastaa

• Tarkista teho: Ensure the plug is securely inserted into a live wall outlet.
• Z-Wave Network: Verify the plug is properly included in your Z-Wave network. If unsure, attempt exclusion and then re-inclusion.
• Alue: The plug might be out of range of your Z-Wave hub or other repeaters. Try moving it closer or adding another repeater.
• Ylikuormitus: Ensure the connected appliance does not exceed the 15A/1875W maximum load.
• Tehdasasetusten palautus: If all else fails, perform a factory reset and attempt re-inclusion.

LED-ilmaisimen toiminta

• Kiinteä PÄÄLLÄ: Device is powered and connected.
• Flashing (during pairing): Device is attempting to include or exclude from the network.
• Ei valoa: Device may not be receiving power or is in an OFF state (depending on hub configuration).

Tekniset tiedot

Takuu ja tuki

Minoston products are designed for reliability and performance. For warranty information, technical support, or further assistance, please refer to the contact information provided with your product packaging or visit the official Minoston websivusto. Säilytä ostokuitti takuuvaatimuksia varten.