Johdanto
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your PEDROLLO JSWm/2CX self-priming water pump. Please read these instructions carefully before installation or use and retain them for future reference.
Kuva 1: PEDROLLO JSWm/2CX Self-Priming Water Pump. This image shows the blue-colored pump unit with its motor housing and pump body, designed for efficient water transfer.
Turvallisuustiedot
Noudata aina seuraavia turvaohjeita välttääksesi pumpun vaurioitumisen tai loukkaantumisen:
- Ensure the pump is installed by a qualified professional.
- Katkaise virta ennen minkään huollon tai huollon suorittamista.
- Do not operate the pump with flammable or corrosive liquids.
- Suojaa pumppu jäätymislämpötiloilta.
- Ensure proper grounding of the electrical connection.
Tuote loppuview
The PEDROLLO JSWm/2CX is a self-priming centrifugal pump designed for reliable water transfer. It is suitable for pumping clean water and liquids that are not chemically aggressive to the pump's components. Its self-priming capability allows it to draw water even when air is present in the suction line, making it ideal for domestic water supply, small to medium autoclave tank systems, and garden irrigation.
Tärkeimmät ominaisuudet:
- Self-priming design for efficient operation.
- Suitable for clean water and non-aggressive liquids.
- Robust construction with stainless steel components.
- Designed for continuous duty in domestic and garden applications.
Asennus ja asennus
Proper installation is crucial for the pump's performance and longevity. Consult a qualified technician for installation.
- Sijainti: Install the pump in a dry, well-ventilated area, protected from direct sunlight and freezing temperatures. Ensure adequate space for maintenance.
- Asennus: Securely fasten the pump to a stable, level surface using appropriate bolts to minimize vibration.
- Putket:
- Use pipes of adequate diameter to minimize friction losses.
- Ensure all connections are airtight, especially on the suction side, to prevent air ingress.
- Install a foot valve with a strainer at the end of the suction pipe to prevent debris from entering the pump and to maintain prime.
- Install a gate valve on both the suction and discharge sides for isolation during maintenance.
- Sähköliitäntä:
- Connect the pump to a suitable power supply (220-230V, 50Hz) as indicated on the motor's data plate.
- Ensure the electrical circuit is protected by a residual current device (RCD) and an appropriately rated circuit breaker.
- Verify proper grounding according to local electrical codes.
- Pohjustus: Before initial startup, completely fill the pump casing and the suction line with clean water through the priming port. This is essential for self-priming pumps to initiate operation.
Käyttöohjeet
- Ensimmäinen käynnistys: After installation and priming, open the discharge valve fully. Switch on the power supply. The pump should start and begin to draw water.
- Jatkuva toiminta: Monitor the pump for unusual noises or vibrations. Ensure the pump is not running dry, as this can cause severe damage.
- Sammuttaa: To stop the pump, switch off the power supply. If the pump is part of an automatic system (e.g., with a pressure switch), it will start and stop automatically based on demand.
- Lämpötilarajat:
- Liquid temperature: up to +40 °C.
- Ambient temperature: -10 °C to +40 °C.
Huolto
Regular maintenance ensures optimal performance and extends the pump's lifespan. Always disconnect power before maintenance.
- Säännölliset tarkastukset: Inspect the pump and piping for leaks, corrosion, or damage.
- Suodattimen puhdistus: Periodically clean the foot valve strainer to prevent blockages and maintain flow.
- Talvistaminen: In areas prone to freezing, drain the pump completely and store it in a warm, dry place, or insulate it adequately to prevent damage from ice expansion.
- Moottorin tarkastus: Ensure the motor's cooling fins are free from dust and debris to prevent overheating.
Vianetsintä
| Ongelma | Mahdollinen syy | Ratkaisu |
|---|---|---|
| Pumppu ei käynnisty | No power supply; Motor overload; Seized impeller. | Check power connection and circuit breaker; Reset thermal overload; Contact service technician. |
| Pumppu käy, mutta vettä ei tule | Pump not primed; Air leak in suction line; Foot valve clogged; Suction lift too high. | Re-prime the pump; Check all suction connections for leaks; Clean foot valve strainer; Reduce suction lift if possible. |
| Reduced flow or pressure | Partial blockage in piping; Worn impeller; Air in system. | Inspect and clear piping; Contact service technician for impeller replacement; Bleed air from system. |
| Liiallinen melu tai tärinä | Cavitation (air in water); Loose mounting; Bearing wear. | Check for air leaks and ensure proper priming; Tighten mounting bolts; Contact service technician. |
Tekniset tiedot
| Parametri | Arvo |
|---|---|
| Malli | JSWm/2CX |
| Merkki | Pedrollo |
| Teho (HP) | 1 hv |
| Voitage / Taajuus | 220-230V / 50Hz |
| Suurin virtausnopeus | 70 litraa minuutissa |
| Nesteen lämpötila -alue | Jopa +40 °C |
| Ympäristön lämpötila-alue | -10 °C - +40 °C |
| Materiaali | Stainless Steel (pump body components) |
| ASIN | B07HMZ2DKQ |
| Kansainvälinen artikkelikoodi | 08052230012515 |
Note: The specification for "Power: 220 Watts" found in some product listings may refer to a specific component or a different metric. The pump's performance is rated at 1 HP.
Takuu ja tuki
For warranty information, technical support, or spare parts, please contact your authorized Pedrollo dealer or visit the official Pedrollo websivusto. Säilytä ostokuitti ostotodistuksena.
Valmistaja: PEDROLLO
