GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Johdanto

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Turvallisuustiedot

VAROITUS: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Varmista, että virta on katkaistu sulakkeesta ennen asennusta.
• Tämä laite on tarkoitettu asennettavaksi kansallisten sähkösäännösten ja paikallisten määräysten mukaisesti.
• Do not use in wet locations or where directly exposed to water.
• Vain sisäkäyttöön.

Pakkauksen sisältö

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Asennusruuvit
• Wire Nuts (may vary by package)
• Käyttöopas (tämä asiakirja)

Asennus ja asennus

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Kytkimen johdotus

1. Katkaise virta: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Vanhan kytkimen poistaminen: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Tunnista johdot:
   • Linja (kuuma): Yleensä musta, tulee sulakkeesta.
   • Ladata: Yleensä musta, menee valaisimeen tai laitteeseen.
   • Neutraali: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Maaperä: Usually green or bare copper.
4. Yhdistä uusi kytkin: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Yhdistä Linja wire to the terminal marked "LINE".
   • Yhdistä Ladata wire to the terminal marked "LOAD".
   • Yhdistä Neutraali wire to the terminal marked "NEUTRAL".
   • Yhdistä Maadoitus wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Asennuskytkin: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. Asenna seinälevy: Attach the new or existing wall plate.
7. Palauta virta: Kytke virta takaisin päälle sulakkeesta.

Kuva 1: Etuosa view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave-yhteyden muodostaminen (pariliitos)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle kerran. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Kytkimen käyttö

Manuaalinen ohjaus

• Paina alkuun of the paddle to turn the connected load ON.
• Paina pohja of the paddle to turn the connected load POIS.

Z-Wave ohjaus

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Huolto

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Puhdistus: Puhdista kytkin pyyhkimällä se pehmeällä,amp kangas. Älä käytä hankaavia puhdistusaineita tai liuottimia.
• Laiteohjelmistopäivitykset: Tarkista GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Yleishoito: Varmista, ettei kytkintä altistata liialliselle kosteudelle tai äärimmäisille lämpötiloille.

Vianetsintä

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle kerran. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Tekniset tiedot

Takuu ja tuki

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl websivustolla tai ota yhteyttä asiakaspalveluun.

Websivusto: www.gocontrol.com

Valmistaja: GOCONTROL