1. Johdanto
This manual provides detailed instructions for the installation, operation, and maintenance of the HOBBYWING XRotor PRO 40A ESC (Dual Pack). This Electronic Speed Controller is designed for multi-rotor applications, offering precise throttle response and compatibility with various flight control systems. Please read this manual thoroughly before use to ensure proper functionality and safety.
2. Turvallisuustiedot
Tärkeitä turvallisuusvaroituksia:
- Always disconnect the battery before handling or performing maintenance on the ESC or motor.
- Ensure correct polarity when connecting the battery to avoid damage to the ESC and other components.
- Käytä ESC:tä sen määritellyllä äänenvoimakkuudellatage and current limits (3-6S Lipo, 40A continuous / 60A peak).
- Pidä ESC poissa vedestä, kosteudesta ja äärimmäisistä lämpötiloista.
- Mount the ESC in a location with adequate airflow to prevent overheating.
- Tämä tuote ei ole lelu. Pidä poissa lasten ulottuvilta.
3. Pakkauksen sisältö
Varmista, että pakkauksessasi on kaikki tarvittavat osat:
- HOBBYWING XRotor PRO 40A ESC (2 units)
- Käyttöohje (tämä asiakirja)
Image: HOBBYWING XRotor PRO 40A ESC (Dual Pack). This image shows the two ESC units with their pre-attached wires.
4. Asennus ja asennus
Follow these steps for proper installation of the XRotor PRO 40A ESC:
- Asennus: Securely mount the ESCs to your multi-rotor frame. Ensure adequate ventilation around each ESC to dissipate heat effectively. Use double-sided tape or zip ties as appropriate for your frame.
- Moottorin liitäntä: Connect the three motor wires from the ESC to the three wires of your brushless motor. The order of connection determines the motor's rotation direction. If the motor spins in the wrong direction, swap any two of the three motor wires.
- Virtaliitäntä: Connect the red (+) and black (-) power wires of the ESC to your flight battery's corresponding terminals. Ensure correct polarity. The ESC supports 3-6S LiPo batteries.
- Signal Cable Connection: Connect the throttle signal cable (usually a single white or yellow wire) from the ESC to the appropriate channel on your flight controller. The twisted-pair design of the throttle signal cable helps reduce signal interference.
- Initial Calibration (if required by flight controller): Refer to your flight controller's manual for ESC calibration procedures. The XRotor PRO 40A ESC is designed for excellent compatibility and often requires minimal setup.
5. Käyttöohjeet
The XRotor PRO 40A ESC is largely plug-and-play due to its pre-set configurations. However, understanding its operation is crucial for optimal performance.
- Kaasuvaste: The special core program for multi-rotor controllers significantly improves throttle response, providing precise control for flight maneuvers.
- Yhteensopivuus: Optimized software ensures excellent compatibility with disc-type motors and various flight control systems. It supports signal frequencies up to 621Hz. Note that throttle signals over 500Hz are non-standard.
- Ajoitus: All settings except "Timing" are pre-set. Adjusting motor timing is typically done via the flight controller or a separate programming card if advanced customization is desired. Refer to your motor's specifications for optimal timing settings.
- DEO Function: The ESC includes a DEO (Driving Efficiency Optimization) function. This can be enabled or disabled, usually through a programming item if available, to further enhance efficiency and response.
6. Huolto
Regular maintenance ensures the longevity and reliable performance of your ESCs:
- Tarkastus: Periodically inspect all wires and solder joints for signs of wear, fraying, or corrosion. Repair or replace damaged components immediately.
- Puhdistus: Keep the ESCs clean and free from dust, dirt, and debris. Use a soft brush or compressed air for cleaning. Avoid using liquids.
- Lämmönhallinta: Ensure the ESCs are not consistently overheating during operation. If they are, check for adequate airflow, proper motor/propeller combination, and correct timing settings.
- Varastointi: When not in use for extended periods, store the ESCs in a dry, cool environment, disconnected from the battery.
7. Vianmääritys
If you encounter issues with your XRotor PRO 40A ESC, refer to the following common problems and solutions:
| Ongelma | Mahdollinen syy | Ratkaisu |
|---|---|---|
| Moottori ei pyöri tai nykii. | Incorrect motor wire connection, ESC not calibrated, faulty motor/ESC. | Check motor wire connections; swap two wires if motor spins wrong way. Perform ESC calibration. Test with a different motor/ESC if possible. |
| ESC gets excessively hot. | Insufficient airflow, overloaded motor, incorrect timing. | Ensure proper ventilation. Check motor/propeller combination for appropriate load. Adjust motor timing if programmable. |
| Intermittent power or signal loss. | Loose connections, damaged wires, signal interference. | Inspect all solder joints and connectors. Ensure signal cable is securely connected and away from power wires. |
| ESC ei käynnisty. | Battery not connected, incorrect battery polarity, faulty battery/ESC. | Verify battery connection and polarity. Test battery voltage. Check for visible damage on ESC. |
8. Tekniset tiedot
| Ominaisuus | Yksityiskohta |
|---|---|
| Malli | 30902042 |
| Jatkuva virta | 40A |
| Huippuvirta | 60A |
| Tulo Voltage | 3-6S LiPo |
| BEC-tyyppi | Ei BEC |
| Applicable Multicopter Class | 550/650 Class Quadcopter |
| Mitat | 5.25 x 3.5 x 2.25 tuumaa (tuotteen mitat) |
| Tuotteen paino | 5.6 unssia |
| Materiaali | Alumiini, Muovi |
| UPC | 088718514408 |
9. Takuu ja tuki
For warranty information and technical support, please contact HOBBYWING North America directly. Details regarding specific warranty periods and conditions are typically provided with the product packaging or on the official HOBBYWING websivusto.
Valmistaja: Hobbywing-teknologia
Ota yhteyttä: Refer to the official HOBBYWING websivustolta löydät ajantasaisimmat tukiyhteystiedot ja resurssit.
