Satco 90-192

Satco 90-192 Brass Finish Ribbed Canopy Kit

Käyttöohje

Johdanto

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Satco 90-192 Brass Finish Ribbed Canopy Kit. Please read all instructions carefully before beginning installation and retain this manual for future reference. This canopy kit is designed to cover electrical connections at the ceiling or wall outlet box for various lighting fixtures.

Turvallisuustiedot

WARNING: RISK OF ELECTRIC SHOCK. Disconnect power at the fuse box or circuit breaker before installation or servicing.

  • Katkaise aina päävirta sulaketaulusta tai sulakekaapista ennen sähkötöiden tekemistä.
  • Jos olet epävarma jostakin asennusprosessin osasta, ota yhteyttä pätevään sähköasentajaan.
  • Varmista, että kaikki sähköliitännät ovat kunnossa ja että ne ovat paikallisten sähkömääräysten mukaisia.
  • Do not install this product in wet locations unless specifically rated for such use.
  • Käsittele kaikkia osia varoen vaurioiden välttämiseksi.

Pakkauksen sisältö

Varmista, että kaikki osat ovat mukana ennen asennuksen aloittamista:

  • 1x Brass Finish Ribbed Canopy (5" Diameter)
  • 1x Mounting Strap/Crossbar
  • 2x Mounting Screws (for outlet box)
  • 2x Canopy Screws/Nuts (for securing canopy)
  • 1x Ground Screw
  • Lankamutterit (määrä voi vaihdella)
Satco 90-192 Brass Finish Ribbed Canopy Kit components

Image: The Satco 90-192 Brass Finish Ribbed Canopy Kit, showing the main canopy piece and associated hardware. This image illustrates the complete set of components included in the package, such as the canopy, mounting strap, and various screws.

Asennus ja asennus

Tools you may need (not included): Screwdriver (Phillips/Flathead), Wire Strippers, Pliers, Electrical Tape, Voltage Testaaja.

  1. Sammuta virta: Locate the circuit breaker or fuse box that controls the power to the fixture location. Turn off the power completely. Use a voltage tester to confirm that the power is off at the outlet box.
  2. Valmistele asennuspinta: If replacing an existing canopy, carefully remove the old fixture. Ensure the electrical outlet box is securely mounted to the ceiling or wall structure.
  3. Install Mounting Strap: Attach the provided mounting strap (crossbar) to the electrical outlet box using the two mounting screws. Ensure the strap is firmly secured and the threaded holes for the canopy screws are facing outwards.
  4. Tee sähköliitännät:
    • Connect the bare copper or green ground wire from the fixture (if applicable) to the ground screw on the mounting strap.
    • Connect the white (neutral) wire from the fixture to the white (neutral) wire from the outlet box using a wire nut.
    • Connect the black (hot) wire from the fixture to the black (hot) wire from the outlet box using a wire nut.
    • Ensure all wire nuts are securely twisted and connections are tight. Wrap electrical tape around wire nuts for added security if desired.
  5. Position Wires: Carefully tuck all connected wires into the outlet box, ensuring no wires are pinched.
  6. Kiinnitä katos: Align the center hole of the canopy over the fixture's wires and the two threaded holes on the mounting strap. Push the canopy flush against the ceiling or wall. Secure the canopy in place using the two canopy screws/nuts, tightening them evenly until the canopy is snug.
  7. Palauta virta: Once the canopy is securely installed, restore power at the circuit breaker or fuse box.
Installation step for Satco 90-192 canopy kit

Image: A conceptual illustration of the canopy being installed onto a ceiling outlet box. This image demonstrates how the canopy covers the electrical connections and is secured by screws, providing a clean finish.

Toiminta ja tarkoitus

The Satco 90-192 Brass Finish Ribbed Canopy Kit serves as a decorative and functional cover for the electrical wiring connections at the ceiling or wall outlet box. It provides a finished appearance to your lighting fixture installation while safely enclosing the electrical components. The 1-1/16" center hole accommodates the stem or chain of most standard lighting fixtures.

Huolto

To maintain the appearance and integrity of your brass finish ribbed canopy kit:

  • Puhdistus: Dust regularly with a soft, dry cloth. For more thorough cleaning, use a slightly damp cloth with mild soap and water. Avoid abrasive cleaners, solvents, or polishes that may damage the finish.
  • Tarkastus: Periodically check that the canopy remains securely fastened to the ceiling or wall. If any looseness is detected, turn off power and re-tighten the canopy screws.

Vianetsintä

Ongelma Mahdollinen syy Ratkaisu
Canopy is loose or wobbles. Canopy screws are not tightened sufficiently. Turn off power. Re-tighten the canopy screws evenly until snug. Do not overtighten.
Canopy does not sit flush against the ceiling/wall. Wires are not properly tucked into the outlet box; mounting strap is not flush. Turn off power. Carefully re-arrange wires inside the outlet box. Ensure the mounting strap is flush with the outlet box.
Viimeistely näyttää himmeältä tai värjäytyneeltä. Accumulation of dust or residue; use of improper cleaning agents. Puhdista pehmeällä, damp liinalla ja miedolla saippualla. Vältä vahvoja kemikaaleja.

Tekniset tiedot

  • Merkki: Satco
  • Malli: 90-192
  • Materiaali: Messinki
  • Viimeistely: Ribbed Brass
  • Halkaisija: 5 tuumaa
  • Center Hole: 1-1/16 tuumaa
  • Asennustyyppi: Kattoon kiinnitys
  • UPC: 045923901928

Takuu ja tuki

This product is covered by Satco's standard manufacturer's warranty. For specific warranty details, claims, or technical support, please contact Satco customer service directly. Keep your purchase receipt as proof of purchase.

For further assistance, please visit the official Satco websivustolta tai ota yhteyttä heidän asiakastukilinjaansa.

Aiheeseen liittyvät asiakirjat - 90-192

Preview Monisuuntaisten LED T8 -putkien asennus- ja turvallisuusohjeet | SATCO
Kattava asennus- ja turvallisuusopas SATCO Omni-Directional LED T8 -putkille (mallit S16430-S16443). Opi asentamaan nämä energiatehokkaat LED-putket turvallisesti olemassa oleviin loisteputkiin. Opas sisältää kytkentäkaaviot ja tärkeät varoitukset.
Preview Satco Hi-Pro LED Lamps 120-277V Asennus- ja turvallisuusohjeet
Kattava asennus- ja turvallisuusopas Satco Hi-Pro LED L:lleamps (mallit S13130-S13136), joka sisältää kytkentäkaaviot, turvallisuusvaroitukset ja asennusohjeet CFL- ja HPS/HID-lamppujen vaihtamiseksiamps.
Preview Satco Starfish WiFi Älykkäät sisä-/ulkokäyttöön tarkoitetut valosarjat, malli S11272, asennus- ja turvallisuusohjeet
Kattava asennus- ja turvallisuusopas Satco Starfish WiFi -älykkäille sisä-/ulkokäyttöön tarkoitetuille valosarjavaloille (malli S11272). Kattaa varoitukset, sisällön, vaiheittaiset asennusohjeet ja sovellusyhteyden.
Preview Starfish WiFi Smart 16' ulkokäyttöön tarkoitetun valonauhan asennus- ja turvallisuusohjeet (malli S11265)
Hanki yksityiskohtaiset asennus- ja turvallisuusohjeet Satco Nuvo Starfish WiFi Smart 16 jalan (malli S11265) ulkokäyttöön tarkoitetulle LED-nauhalle. Opi sähköturvallisuudesta, asianmukaisesta asennuksesta ja sovelluksen kytkemisestä.
Preview Satco 7" ja 10" LED-levyvalojen asennus- ja turvallisuusohjeet
Kattava asennus- ja turvallisuusopas Satcon 7- ja 10-tuumaisille LED-levyvaloille (mallit 62/1660-62/1673), mukaan lukien kytkentäkaaviot ja vaiheittaiset ohjeet.
Preview SATCO LED T8U-Bend käyttöohjeet ja kytkentäopas
Yksityiskohtaiset käyttöohjeet, turvaohjeet ja kytkentäkaaviot SATCO LED T8U-Bend -jälkiasennussarjoille, mukaan lukien mallit S9930, S9931, S9932 ja S9933. Kattaa asennuksen, yhteensopivuuden ja FCC-vaatimustenmukaisuuden.