RGBlink NDI PTZ Camera Controller (RGBBKT) User Manual

1. Johdanto

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of the RGBlink NDI PTZ Camera Controller (RGBBKT). This device is designed for professional video production environments, offering comprehensive control over various PTZ cameras using multiple protocols.

Image 1.1: RGBlink NDI PTZ Camera Controller (RGBBKT).

2. Asennus

Follow these steps to set up your RGBlink NDI PTZ Camera Controller.

2.1 Pakkauksesta purkaminen ja alkutarkastus

• Poista kaikki osat varovasti pakkauksesta.
• Varmista, että kaikki pakkauslistassa luetellut tavarat ovat mukana.
• Inspect the controller for any signs of physical damage. If damage is found, contact your dealer immediately.

2.2 Ohjaimen liittäminen

The RGBlink NDI PTZ Camera Controller supports various connection methods for power and camera control.

• Power over Ethernet (PoE): Connect a single RJ45 Ethernet cable from a PoE-enabled network switch to the controller's LAN port. This provides both power and network connectivity.
• Ulkoinen virtalähde: If PoE is not available, connect the provided power adapter to the DC 12V input port and to a power outlet.
• Kameran liitännät:
  • Ethernet (IP Control): Connect PTZ cameras to the same network as the controller via RJ45 Ethernet cables. The controller supports VISCA over IP, ONVIF v2.42, and NDI v5.5 protocols.
  • Sarjaohjaus: For cameras supporting serial communication, use RS232, RS422, or RS485 interfaces. Connect the appropriate cables from the controller's serial ports to the cameras.

Image 2.1: Rear panel connections including RS-232, RS-422, LAN (PoE), and Power Input.

Kuva 2.2: Esim.ample connection diagram showing PTZ Controller, PoE Switch, PTZ Cameras, Audio Mixer, and Computer.

Image 2.3: Diagram illustrating IP camera connections via a network switch.

2.3 Verkkoasetukset

For IP-based camera control, ensure the controller and cameras are on the same network segment. The controller supports automatic detection of NDI-enabled PTZ cameras.

• Käytä ohjaimen web käyttöliittymä syöttämällä sen IP-osoite kohtaan a web browser. (Refer to the device's display or network tools to find the IP address).
• The default login credentials are typically 'admin' with a blank password. It is recommended to set a strong password immediately.
• Sisällä web interface, configure camera protocols (e.g., ONVIF, VISCA over IP) and enter camera-specific user credentials if required.

Image 2.4: NDI|HX camera search and control interface on the controller.

3. Käyttö

This section details the operational functions of the RGBlink NDI PTZ Camera Controller.

3.1 Yliview säätimistä

The controller features a 3.49" LCD display, a 3D joystick, various knobs, and a numeric keypad for intuitive control.

Image 3.1: The controller's 3.49-inch LCD display.

Kuva 3.2: Yksityiskohtainen view of the 3D joystick and multi-function knobs.

Image 3.3: Layout of the controller's buttons and numeric keypad area.

3.2 Kameran valinta

• Pikavalintapainikkeet: Use the dedicated CAM 1-5 buttons for quick selection of up to 5 cameras.
• Numeronäppäimistö: For cameras beyond the quick select buttons (up to 255), press the CAM -tunnus button, then enter the camera number using the numeric keypad, and press ENTER.

Image 3.4: The controller's ability to manage multiple cameras.

3.3 PTZ-ohjaus

• joystick: The 3D joystick controls pan (left/right), tilt (up/down), and zoom (rotate the joystick).
• PT-nopeusnuppi: Adjusts the gimbal movement speed for pan and tilt.
• Zoom Knob: Provides precise zoom control, especially useful in preview tila.

3.4 Image Parameter Adjustment

• IRIS/SHUTTER Knob: Rotate to adjust aperture and shutter speed. Press to switch control modes.
• R/B GAIN Knob: Rotate to adjust red and blue gain. Press to switch control modes.
• FOCUS Button: Paina AUTO FOCUS button to switch the camera to auto focus mode.
• EXPOSURE Button: Cycles through exposure modes (Aperture Priority, Shutter Priority, Gain Priority, Manual Exposure, Auto Exposure).
• TAUSTAVALON painike: Toggles the camera's backlight mode.
• WHITE BALANCE CYCLE Button: Cycles through white balance modes (Indoor, Outdoor, Manual, Auto).
• ONE PUSH TRIGGER Button: When white balance is set to "One-Push White Balance", press this button to initiate a one-push white balance calibration.

Image 3.5: Functions of buttons and knobs on the left side of the controller.

Image 3.6: Functions of buttons and knobs on the right side of the controller, including preset controls.

3.5 esiasetusta

• SET PRESET Button: Press to enter preset position mode. Use the numeric keys to enter the preset number (0-9) and press ENTER pelastaa. Lehdistö ESC poistuaksesi.
• CALL PRESET Button: Press to enter preset recall mode. Use the numeric keys to enter the preset number (0-9) and press ENTER to recall. Press ESC poistuaksesi.
• The controller supports saving and recalling up to 255 presets per camera.

3.6 Navigointi valikossa

• MENU-painike: Press to open or close the camera settings menu. In menu control mode, the joystick controls navigation (up, down, left, right), ENTER confirms selections, and ESC acts as a back button.

4. Huolto

Proper maintenance ensures the longevity and optimal performance of your RGBlink NDI PTZ Camera Controller.

4.1 Puhdistus

• Use a soft, dry cloth to clean the exterior of the controller.
• Pinttyneeseen likaan, kevyesti dampKostuta liina vedellä tai miedolla, hankaamattomalla puhdistusliuoksella.
• Avoid using harsh chemicals, solvents, or abrasive materials, as these can damage the surface and display.
• Ensure no liquids enter the device through openings or ports.

4.2 Varastointi

• When not in use for extended periods, store the controller in a cool, dry place away from direct sunlight and extreme temperatures.
• Suojaa laitetta pölyltä ja kosteudelta.

5. Vianmääritys

Tässä osiossa on ratkaisuja yleisiin ongelmiin, joita saatat kohdata.

5.1 Ei virtaa

• Tarkista virtalähde: Varmista, että virtalähde on kytketty kunnolla sekä ohjaimeen että toimivaan pistorasiaan.
• PoE Check: If using PoE, verify that the Ethernet cable is connected to a PoE-enabled port on your network switch and that the switch is powered on.
• Kaapelin eheys: Inspect the power cable and Ethernet cable for any damage.

5.2 Cannot Control Camera

• Verkkoyhteydet: For IP cameras, ensure the controller and cameras are on the same network and can communicate. Check network cables and IP addresses.
• Protokollan yhteensopimattomuus: Verify that the correct control protocol (e.g., VISCA over IP, ONVIF, NDI, Pelco-D/P) is selected on both the controller and the camera.
• Kameran tunnus: Ensure the correct camera ID is selected on the controller.
• Kirjautumistiedot: If the camera requires authentication, confirm that the correct username and password are configured in the controller's web käyttöliittymä.
• Sarjaliitäntä: For serial control, check RS232/RS422/RS485 cable connections and ensure baud rates and addresses match between the controller and camera.
• Laiteohjelmisto: Ensure both the controller and cameras have the latest firmware installed. Visit the RGBlink support websivusto päivityksiä varten.

5.3 LCD-näytön ongelmat

• Ei näyttöä: Varmista, että ohjaimeen on kytketty virta.
• Himmeä näyttö: Check if there are any brightness settings on the controller that can be adjusted.

6. Tekniset tiedot

Image 6.1: Controller dimensions and typical usage environments.

Image 6.2: Visual representation of supported protocols including RJ45, RS485, RS422, RS232, ONVIF, NDI, Pelco-D, Pelco-P, and Visca.

7. Tuotevideoesittely

Watch the official product video for a visual demonstration of the RGBlink NDI PTZ Camera Controller's features and operation.

8. Takuu ja tuki

For warranty information, technical support, or service inquiries, please contact RGBlink customer service or visit their official websivusto.

• Valmistaja: Xiamen RGBlink Science & Technology Co.,Ltd.
• Virallinen Websivusto: www.rgblink.com (Huomautus: Tämä on paikkamerkki URL, please refer to your product packaging or official documentation for the correct support websivusto.)
• Yhteystiedot: Refer to the RGBlink official website for the most current contact details for technical support and warranty claims.