MOUNTUP Dual Monitor Arm MU8012-W-07 Instruction Manual

1. Johdanto

Thank you for choosing the MOUNTUP Dual Monitor Arm MU8012-W-07. This instruction manual provides essential information for the safe and correct installation, operation, and maintenance of your new monitor arm. Please read this manual thoroughly before installation and keep it for future reference.

Turvallisuusohjeet

Varmista, että kaikki osat ovat mukana ja vahingoittumattomia ennen kokoamista. Älä käytä laitetta, jos jokin osa puuttuu tai on viallinen.
Verify that your desk surface is strong enough to support the combined weight of the monitor arm and your monitors.
Do not exceed the maximum weight capacity of 10kg (22 lbs) per arm.
Always follow the installation steps carefully. Improper installation may result in product damage or personal injury.
Keep children away from the product during assembly. Small parts may be a choking hazard.

MOUNTUP Dual Monitor Arm supporting two monitors on a desk, illustrating a dual monitor setup for enhanced productivity. — MOUNTUP Dual Monitor Arm in a typical dual monitor setup, enhancing workspace efficiency.

2. Pakkauksen sisältö

Tarkista, että pakkauksessasi on kaikki seuraavat osat:

Monitor Arm Assembly (x1)
VESA-levy (x2)
Työpöytä Clamp Pohja (x1)
Grommet Base (x1)
Mounting Hardware Kit (screws, washers, spacers)
Kuusiokoloavaimet (eri kokoisia)
Käyttöohje (x1)

3. Tekniset tiedot

Ominaisuus	Erittely
Malli	MU8012-W-07
Materiaali	Seosteräs
Väri	Valkoinen
Näytön koon yhteensopivuus	13–32 tuumaa
Painokapasiteetti (vartta kohden)	2–10 kg (4.4–22 paunaa)
VESA-yhteensopivuus	75x75mm, 100x100mm
Asennusvaihtoehdot	Clamp, Läpivienti
Kallistusalue	+85° - -45°
Kääntöalue	180° (monitor plate), 270° (middle joint), 360° (base)
Rotation (Pivot)	360°
Maksimi korkeuden säätö	44 cm (17.3 tuumaa)
Max-varren jatke	50 cm (19.7 tuumaa)
Tuotteen paino	3.1 kg (6.8 lbs)

Diagram showing monitor compatibility requirements: 13-32 inch screen size, 2-10kg weight capacity, and VESA 75x75mm or 100x100mm mounting patterns. — Ensure your monitors meet the size, weight, and VESA compatibility requirements.

4. Asennus ja asennus

Vaihe 1: Valitse kiinnitystapasi

The MOUNTUP Dual Monitor Arm supports two installation methods: Clamp Mount and Grommet Mount. Choose the method that best suits your desk.

Comparison image showing two installation methods: clamp mounting on the right and grommet mounting on the left, with desk thickness requirements. — Two common installation methods: Clamp (right) and Grommet (left).

Clamp Kiinnikkeen asennus

Kiinnitä clamp base to the main pole of the monitor arm.
Aseta clamp onto the edge of your desk. Ensure the desk thickness is between 10-70mm (0.4-2.7 inches).
Kiristä clamp screw until the arm is securely fastened to the desk. Ensure it is stable and does not wobble.

Detailed illustrations of clamp installation, showing compatibility with different desk edge types (with bottom frame, side panel, back panel) and required dimensions. — Clamp installation details for various desk configurations.

Läpivientikiinnikkeen asennus

If your desk has a grommet hole, ensure its diameter is between 10-60mm (0.4-2.4 inches) and the desk thickness is between 10-70mm (0.4-2.7 inches).
Attach the grommet base to the main pole.
Työnnä läpivientipultti pöydän reiän läpi ja kiinnitä se alapuolelta mukana toimitetulla levyllä ja mutterilla.
Tighten the nut until the arm is firmly attached to the desk.

Vaihe 2: Kiinnitä VESA-levyt monitoreihin

Carefully lay your monitor face down on a soft, clean surface.
Kohdista VESA-levy näytön takana oleviin kiinnitysreikiin.
Use the appropriate screws (M4 or M5) and washers from the hardware kit to secure the VESA plate to the monitor. Do not overtighten.

Vaihe 3: Kiinnitä näytöt varsiin

Slide the monitor (with the attached VESA plate) onto the VESA head of the monitor arm.
Ensure the monitor clicks into place or is securely fastened by the quick-release mechanism.
Toista toiselle näytölle.

Image showing the quick-release VESA plate mechanism for easy attachment and detachment of monitors. — Quick-release VESA plate for easy monitor attachment and detachment.

Vaihe 4: Kaapelin hallinta

Route your monitor cables through the integrated cable management clips on the underside of the arms. This helps maintain a tidy workspace.

Takaosa view of the monitor arm with cables neatly routed through integrated cable management clips and a compartment for hex wrench storage. — Integrated cable management keeps your workspace organized. Hex wrenches can be stored in the arm base.

5. Käyttö ja säädöt

The MOUNTUP Dual Monitor Arm offers flexible adjustments to optimize your viewkokemusta.

Four panels demonstrating various monitor adjustments: 180-degree left/right swivel, 130-440mm height adjustment, +85 to -45 degree tilt, and 360-degree rotation (pivot). — Yliview of the monitor arm's extensive adjustment capabilities.

Adjusting Arm Tension (Gas Spring)

The gas spring mechanism allows for smooth height adjustments. If your monitor sags or is difficult to move, you may need to adjust the tension.

Instructions for adjusting the gas spring tension for both tilt and arm height, with diagrams showing clockwise for increasing tension and counter-clockwise for decreasing-jännite. — Adjusting gas spring tension for optimal monitor positioning.

To increase tension (if monitor sags): Use the provided hex wrench to turn the adjustment screw clockwise.
To decrease tension (if arm is too stiff): Turn the adjustment screw counter-clockwise.
Always adjust tension with the arm held horizontally. Test the movement after each small adjustment until the monitor holds its position freely.

Näytön säädöt

Korkeuden säätö: Gently push or pull the monitor up or down to your desired height. The gas spring will assist in holding the position. Max height is 44cm (17.3 inches).
Kallistuksen säätö: Tilt the monitor screen up to +85° or down to -45° to reduce glare and optimize viewing angles. Loosen the tilt bolt, adjust, then re-tighten.
Kääntymisen säätö: The arm allows for 180° swivel at the monitor plate, 270° at the middle joint, and 360° at the base, providing wide range of motion.
Kierto (Pivot): Rotate your monitor 360° to switch between landscape and portrait orientations.

Diagram illustrating the multi-angle adjustment capabilities of the monitor arm, including 180-degree swivel at the monitor, 270-degree swivel at the middle joint, and 360-degree swivel at the base. — Detailed swivel capabilities of the monitor arm joints.

Sivu view of the MOUNTUP monitor arm showing maximum height adjustment of 44cm and maximum extension of 50cm. — Maximum height and extension capabilities of the monitor arm.

6. Huolto

Puhdistus: Pyyhi näytön varsi pehmeällä,amp liinalla. Vältä hankaavia puhdistusaineita tai liuottimia, jotka voivat vahingoittaa pintaa.
Säännölliset tarkastukset: Tarkista säännöllisesti kaikki ruuvit ja liitokset varmistaaksesi, että ne ovat kireällä. Kiristä tarvittaessa uudelleen.
Gas Spring Longevity: The high-quality gas spring is tested for over 20,000 cycles. Proper tension adjustment will help maintain its performance over time.

Close-up of the high-quality gas spring mechanism within the monitor arm, highlighting its durability with a '20,000 cycle test' label. — The durable gas spring is designed for long-lasting performance.

7. Vianmääritys

Monitor Sags or Won't Stay Up: The gas spring tension is too low. Refer to the "Adjusting Arm Tension" section and turn the adjustment screw clockwise to increase tension.
Arm is Too Stiff or Difficult to Move: The gas spring tension is too high. Refer to the "Adjusting Arm Tension" section and turn the adjustment screw counter-clockwise to decrease tension.
Näytön heiluminen: Ensure all mounting screws (VESA plate to monitor, arm to desk) are securely tightened. Check that the desk clamp or grommet mount is firm.
Monitor Tilt Angle Won't Hold: The tilt bolt may be loose. Tighten the tilt bolt on the VESA head.

8. Takuu ja tuki

MOUNTUP provides a 2 vuoden laatutakuu from the date of purchase for this product. This warranty covers manufacturing defects and issues arising from normal use.

If you encounter any problems with your MOUNTUP Dual Monitor Arm, or if you have questions regarding installation or operation, please contact our customer support. You can typically find seller contact information through your purchase history on the platform where you bought the product (e.g., Amazon order details).

Please have your model number (MU8012-W-07) and purchase date ready when contacting support to ensure a swift resolution.

MOUNTUP MU8012-W-07