1. Johdanto
Thank you for choosing the Srutueo S810 E-Bike Meter LED Display. This manual provides essential information for the proper installation, operation, and maintenance of your new e-bike display. Please read this manual thoroughly before use to ensure optimal performance and safety.
2. Turvallisuustiedot
- Always ensure your e-bike is powered off before connecting or disconnecting the display.
- Do not attempt to open or modify the display unit. Unauthorized modifications can void the warranty and cause damage.
- Pidä näyttö poissa äärimmäisistä lämpötiloista, pitkäaikaisesta suorasta auringonvalosta ja syövyttävistä aineista.
- The display is IP65 rated for water and dust resistance, but avoid submerging it in water.
- Ensure all connections are secure to prevent accidental disconnections during operation.
3. Tuote ohiview
3.1 Pakkauksen sisältö
- 1 x Srutueo S810 E-Bike Meter LED Display
3.2 Näytön ominaisuudet
The S810 LED display provides essential information and controls for your electric bicycle.
Kuva: Edessä view of the Srutueo S810 E-Bike Meter LED Display, showing the ON/OFF, LIGHT, and MODE buttons, power indicator LEDs, assist level LEDs (LOW, MED, HIGH), and the 6-pin UART connector detail in the upper right corner.
- ON/OFF-painike: Powers the e-bike system on or off.
- VALO -painike: Controls the e-bike's headlight (if connected and supported by the controller).
- MODE-painike: Cycles through assist levels (LOW, MED, HIGH).
- Power Indicator LEDs: Four red LEDs indicate the current battery charge level.
- Assist Level LEDs: Three LEDs (LOW, MED, HIGH) indicate the selected pedal assist level.
- 6PIN UART Connector: Standard connector for communication with the e-bike controller.
4. Asennus ja asennus
4.1 Näytön kiinnittäminen
- Choose a suitable location on your e-bike handlebars that allows for easy visibility and access to buttons without obstructing your view tai ohjaimia.
- Securely attach the display bracket (not included, typically part of the e-bike's existing setup) to the handlebars.
- Slide the S810 display onto the bracket until it clicks into place.
4.2 Näytön kytkeminen
Kuva: Edessä view of the Srutueo S810 E-Bike Meter LED Display, highlighting the green 6-pin UART connector at the bottom right.
- Locate the corresponding 6-pin UART connector on your e-bike's controller wiring harness.
- Align the pins carefully and firmly push the display's connector into the controller's connector until it is fully seated.
- Ensure the connection is secure and waterproof.
5. Käyttöohjeet
5.1 Virta päälle/pois
- To power on the e-bike system, press and hold the ON/OFF button for approximately 2 seconds. The display LEDs will illuminate.
- To power off the e-bike system, press and hold the ON/OFF button again for approximately 2 seconds. The display LEDs will turn off.
5.2 Avustustasojen muuttaminen
- Paina MODE button repeatedly to cycle through the pedal assist levels: LOW, MED, HIGH.
- The corresponding LED (LOW, MED, or HIGH) will illuminate to indicate the currently selected assist level.
5.3 Activating Headlight
- If your e-bike is equipped with a headlight connected to the controller, press the VALOA button to turn the headlight on or off.
5.4 Akun varauksen ilmaisin
- The four red LEDs under 'POWER' indicate the remaining battery charge.
- Four LEDs lit: Full charge.
- One LED lit: Low charge, recharge battery soon.
6. Huolto
- Puhdistus: Käytä pehmeää, damp cloth to wipe the display surface. Do not use abrasive cleaners or solvents.
- Varastointi: When not in use for extended periods, store the e-bike and display in a cool, dry place, away from direct sunlight.
- Tarkastus: Periodically check the connector for any signs of wear or damage. Ensure it remains securely connected.
7. Vianmääritys
| Ongelma | Mahdollinen syy | Ratkaisu |
|---|---|---|
| Näyttö ei käynnisty. | Loose connection, low e-bike battery, faulty display/controller. | Check all connections. Ensure e-bike battery is charged. If problem persists, consult a qualified technician. |
| Assist levels do not change. | Faulty MODE button, communication issue with controller. | Ensure the MODE button is functioning. Check display-to-controller connection. |
| Ajovalo ei syty. | Headlight not connected, faulty headlight, controller not supporting headlight function via display. | Verify headlight connection and functionality. Confirm controller compatibility. |
| Battery indicator is inaccurate. | Battery issue, communication issue. | Check e-bike battery health. Ensure secure connection. |
8. Tekniset tiedot
| Ominaisuus | Erittely |
|---|---|
| Malli | S810 |
| Voitage | 36V (compatible with 36V e-bike systems) |
| Liittimen tyyppi | 6PIN UART |
| Materiaali | Akryylinitriilibutadieenistyreeni (ABS) |
| Ingress Protection (IP) -luokitus | IP65 (Dust tight and protected against low-pressure water jets) |
| Väri | Musta |
| Mitat | Noin 4.33 x 3.94 x 3.15 cm (pakkauksen mitat) |
| Paino | Noin 3.03 unssia (pakkauksen paino) |
9. Takuu ja tuki
This product is covered by a standard manufacturer's warranty. For specific warranty details, please refer to the documentation provided at the time of purchase or contact your retailer. For technical support, troubleshooting assistance beyond this manual, or replacement parts, please contact Srutueo customer service through your purchase platform or the official brand channels.