YOSEC Gun Safe Replacement Electronic Keypad Lock (Model E-816B) User Manual

1. Johdanto

This manual provides detailed instructions for the installation, programming, operation, and maintenance of your YOSEC Gun Safe Replacement Electronic Keypad Lock, Model E-816B. This electronic lock is designed to replace most existing gun safe keypads, offering enhanced security with programmable user and master codes.

Figure 1: YOSEC Electronic Keypad Lock (Model E-816B)

2. Turvallisuustiedot

• Ammattimainen asennussuositus: It is strongly advised that installation and replacement of this keypad be performed by a qualified safe technician or professional locksmith. Improper installation may compromise the safe's security or damage the lock.
• Akun turvallisuus: Use only one 9V lithium battery. Ensure correct polarity when inserting. Do not mix old and new batteries or different types of batteries. Remove batteries if the lock will not be used for an extended period.
• Koodin suojaus: Keep your user and master codes confidential. Do not write them down where they can be easily found. Regularly change your codes for optimal security.
• Lapset ja luvaton pääsy: Always ensure the safe is securely locked and codes are not accessible to children or unauthorized individuals.

3. Pakkauksen sisältö

Varmista, että kaikki osat ovat mukana ennen asennuksen aloittamista:

• Elektroninen näppäimistö
• Solenoidi
• Reset-painike
• Painettu piirilevy (PCB)
• Käyttöopas

Figure 2: Included components: Keypad, Solenoid, Motherboard (PCB), Battery connector, and Programming Cable (Reset Button).

4. Asennus ja ohjelmointi

4.1. Initial Assembly (Pre-Installation)

Before installing the lock onto your safe, it is recommended to assemble the components and test the programming. This allows for easier code setup and verification.

1. Yhdistä komponentit: Carefully connect the keypad, solenoid, and reset button to the Printed Circuit Board (PCB) using the provided cables. Ensure all connections are secure.
2. Asenna akku: Connect a new 9V lithium battery to the battery connector.

Figure 3: Keypad, motherboard, solenoid, and reset button connected for testing.

4.2. Programming User and Master Codes

The lock comes with a factory default user code of "168" and a master code of "12345678". It is crucial to change these default codes immediately for security purposes.

To Change the Master Code:

1. Input the factory default master code: 12345678.
2. Paina # key to confirm. The solenoid should retract, indicating the lock is open.
3. While the lock is open, input 00 näppäimistössä.
4. Press the red reset button (connected to the PCB). The buzzer will beep twice.
5. Enter your new 1-8 digit master code.
6. Paina * key to confirm. The buzzer will beep once to confirm the new master code is set.

To Change a User Code:

The lock supports two group codes (user codes). The process is similar to changing the master code.

1. Input the current user code (default is 168).
2. Paina # key to confirm. The solenoid should retract.
3. While the lock is open, input 00 näppäimistössä.
4. Press the red reset button. The buzzer will beep twice.
5. Enter your new 1-8 digit user code.
6. Paina * key to confirm. The buzzer will beep once to confirm the new user code is set.

Note: The system can be initialized to factory default mode by pressing the reset button when the lock is in a closed state and then entering the default master code.

5. Käyttö

5.1. Kassakaapin avaaminen

1. Enter your 1-8 digit user code or master code on the keypad.
2. Paina # avain vahvistaaksesi.
3. If the code is correct, the solenoid will retract, and the green light will illuminate. You will have a few seconds to turn the safe handle and open the door.

Kuva 4: Lähikuva view of the electronic keypad.

5.2. Kassakaapin sulkeminen

To close the safe, simply close the door and turn the handle to engage the locking bolts. The electronic lock will automatically secure the safe.

6. Huolto

6.1. Pariston vaihto

The lock requires one 9V lithium battery. A low battery warning is indicated by the red light illuminating after opening the safe.

1. When the low battery warning appears, replace the 9V battery promptly.
2. To replace, carefully open the battery compartment (typically located on the inside of the safe door, connected to the PCB).
3. Disconnect the old battery and connect a new 9V lithium battery, ensuring correct polarity.
4. Sulje paristolokero.

Note: Your programmed codes will be retained during battery replacement.

7. Vianmääritys

• Lukitustila: If an incorrect code is entered 3 times consecutively, the lock will enter a 15-minute lockout period. During this time, the keypad will not respond to input. Wait for the lockout period to expire before attempting to enter the code again.
• Alhaisen akun varoitus: If the red light illuminates after opening the safe, the battery is low. Replace the 9V battery as soon as possible to ensure continued operation.
• No Response from Keypad:
  • Check if the battery is properly connected and has sufficient charge.
  • Ensure all cable connections to the PCB are secure.
  • If the issue persists, consider performing a factory reset (see "To Change Code" section for reset button usage).
• Solenoid Not Retracting:
  • Verify that the correct code has been entered and confirmed with the '#' key.
  • Tarkista akun varaustaso.
  • Inspect the solenoid for any obstructions or damage.

8. Tekniset tiedot

9. Takuu ja tuki

For any questions, technical assistance, or support regarding your YOSEC Electronic Keypad Lock, please do not hesitate to contact YOSEC customer service. Refer to your purchase documentation or the retailer's websivustolta tarkempia yhteystietoja varten.

Note: Warranty details may vary by region and retailer. Please retain your proof of purchase for warranty claims.