lightmaXX LED-kaihdin 2 - Käyttöohje

1. Johdanto

Thank you for choosing the lightmaXX LED Blinder 2. This professional stage lighting fixture is designed to provide powerful and versatile illumination for various applications. Featuring two 50-watt warm white COB LEDs, DMX control, and a strobe function, it offers robust performance and flexible integration into your lighting setup. Please read this manual thoroughly before operation to ensure safe and optimal use of your device.

2. Turvallisuusohjeet

Noudata aina seuraavia turvaohjeita sähköiskun, tulipalon tai loukkaantumisen välttämiseksi:

• Tämä laite on tarkoitettu vain ammattikäyttöön.
• Varmista virtalähteen voltage vastaa laitteen vaatimuksia.
• Älä altista laitetta sateelle tai kosteudelle.
• Liitä laite aina maadoitettuun pistorasiaan.
• Älä avaa koteloa. Sen sisällä ei ole käyttäjän huollettavia osia. Jätä kaikki huoltotyöt pätevän henkilöstön tehtäväksi.
• Vältä silmien suoraa altistumista valonlähteelle.
• Varmista riittävä ilmanvaihto laitteen ympärillä ylikuumenemisen estämiseksi.
• Always secure the device with a safety cable when mounting overhead.
• Irrota virtalähteestä ennen puhdistusta tai huoltoa.

3. Tuote ohiview

The lightmaXX LED Blinder 2 features a robust design with two powerful COB LEDs and intuitive controls.

Kuva 3.1: Etuosa view of the lightmaXX LED Blinder 2, showing the two illuminated COB LEDs.

Kuva 3.2: Etuosa view of the lightmaXX LED Blinder 2, illustrating the power cable connection point.

Figure 3.3: Rear panel of the lightmaXX LED Blinder 2, detailing the control display, DMX In/Out, Power In/Out, and safety rope attachment point.

Figure 3.4: Close-up of the control panel, showing the digital display and navigation buttons (MENU, UP, DOWN, ENTER).

3.1 Komponentit

• 2 x 50W Warm White COB LEDs
• Digital Display and Control Buttons (MENU, UP, DOWN, ENTER)
• DMX In/Out (3-pin XLR)
• Power In/Out (IEC)
• Säädettävä kiinnike
• Safety Rope Attachment Point

4. Asennus

4.1 Asennus

The lightmaXX LED Blinder 2 comes with a versatile mounting bracket for truss, floor, or stand mounting. Ensure the mounting surface or structure can safely support the weight of the fixture. Always use a safety cable (not included) when mounting the unit overhead to prevent accidental falls.

• Attach the mounting bracket securely to a truss clamp tai seisoa.
• Adjust the angle of the fixture using the side knobs on the bracket.
• Connect a safety cable from the fixture's safety rope attachment point to the mounting structure.

4.2 Virtaliitäntä

Connect the supplied power cable to the "POWER IN" IEC connector on the rear of the unit and then to a suitable grounded power outlet. The "POWER OUT" connector allows for daisy-chaining power to multiple units (check maximum power draw before connecting multiple units).

4.3 DMX-liitäntä (valinnainen)

For DMX control, connect a DMX cable from your DMX controller's output to the "DMX IN" port on the blinder. To daisy-chain multiple DMX fixtures, connect a DMX cable from the "DMX OUT" port of the first blinder to the "DMX IN" port of the next fixture in the chain. Terminate the last fixture in the DMX chain with a DMX terminator.

5. Käyttöohjeet

5.1 Ohjauspaneelin käyttö

Use the four buttons on the rear panel to navigate the menu and adjust settings:

• VALIKKO: Enters the menu or goes back to the previous menu level.
• YLÖS: Scrolls up through menu options or increases a value.
• ALAS: Scrolls down through menu options or decreases a value.
• TULLA SISÄÄN: Vahvistaa valinnan tai siirtyy alivalikkoon.

5.2 DMX Modes and Channel Assignment

The lightmaXX LED Blinder 2 supports 6 DMX channels. Refer to the DMX chart below for specific channel functions. Set the DMX address using the control panel. The default DMX address is A001.

5.3 Standalone Modes

The blinder can operate without a DMX controller using its built-in programs or sound-activated mode. Access these modes via the control panel menu.

• Automaattitila: Käy läpi esiohjelmoituja valosarjoja.
• Äänen aktiivinen tila: The light reacts to ambient sound via the built-in microphone.
• Manual Dimmer: Adjust the brightness of each LED directly from the menu.

6. Huolto

Regular maintenance ensures the longevity and optimal performance of your lightmaXX LED Blinder 2.

• Puhdistus: Disconnect the power before cleaning. Use a soft, lint-free cloth to wipe the exterior. For stubborn dirt, a slightly damp liinaa voi käyttää. Älä käytä hankaavia puhdistusaineita tai liuottimia.
• Fan and Vent Cleaning: Periodically check and clean the cooling fan and ventilation openings to ensure proper airflow and prevent overheating. Use compressed air to remove dust.
• Kaapelin tarkastus: Regularly inspect power and DMX cables for any signs of damage (cuts, frayed wires). Replace damaged cables immediately.
• Varastointi: When not in use, store the fixture in a dry, dust-free environment, preferably in its original packaging or a suitable flight case.

7. Vianmääritys

If you encounter issues with your lightmaXX LED Blinder 2, refer to the following common problems and solutions:

If the problem persists after trying these solutions, please contact lightmaXX customer support or your authorized dealer.

8. Tekniset tiedot

9. Takuu ja tuki

Specific warranty information for the lightmaXX LED Blinder 2 is not provided in this manual. Please refer to your purchase documentation, the lightmaXX official website, or contact your retailer for details regarding warranty coverage and terms.

For technical support, service, or spare parts inquiries, please contact lightmaXX customer service or your authorized dealer. Ensure you have your model number (LIG0016526-000) and purchase date available when contacting support.

Manufacturer: lightmaXX