Docooler JINGSHA X99-8D3 Motherboard User Manual

1. Johdanto ja loppuview

The Docooler JINGSHA X99-8D3 is a high-performance ATX gaming motherboard designed for LGA2011 V3 processors. It features four-channel DDR3 memory support, an M.2 NVME slot for high-speed storage, and multiple PCI-E expansion slots, making it suitable for demanding computing tasks and gaming setups. This manual will guide you through the installation, configuration, and maintenance of your motherboard.

Kuva 1.1: Ylhäältä alas view of the Docooler JINGSHA X99-8D3 Motherboard, showcasing its layout with CPU socket, RAM slots, and various expansion slots.

2. Tärkeimmät ominaisuudet

• M.2 NVME Support: Equipped with an M.2 hard disk port, supporting high-speed PCI-E NVME X4 for optimal operating system and application driver performance.
• Quad-Channel DDR3 Memory: Features 8 DDR3 memory slots across 4 channels, significantly improving capacity and performance, supporting up to 256GB.
• Digitaalinen diagnostiikkakortti: Integrated digital diagnostic card automatically tests hardware devices to ensure proper operation and assist in troubleshooting.
• Multiple PCI-E Expansion Slots: Provides 3 PCI-E expanded slots, configurable as X16/X8 to handle various workloads and multi-GPU setups.
• Kestävä rakenne: Built with a 10-layer PCB and high-quality capacitors for enhanced stability and heat resistance.

Figure 2.1: Diagram illustrating the six core technologies and features of the motherboard, including 4-channel DDR3*8, M.2 hard disk interface, digital diagnostic card, 7.1 channel audio, SATA3.0*8 interface, and Crossfire support.

3. Pakkauksen sisältö

Varmista, että pakkauksessasi on kaikki alla luetellut tuotteet:

• 1x Docooler JINGSHA X99-8D3 Motherboard
• 1x SATA-kaapeli
• 1x I/O Baffle (Backplate)
• 1x CPU Fan Board
• A bag of screws

4. Tekniset tiedot

Kuva 4.1: Yksityiskohtainen view of the motherboard's rear I/O panel, showing PS/2 ports, USB 2.0, USB 3.0, Gigabit Network Port, and 7.1 Audio Ports.

5. Asennus ja asennus

Ennen asennuksen aloittamista varmista, että järjestelmä on sammutettu ja irrotettu pistorasiasta. Käsittele emolevyä reunoista staattisen sähkön purkauksen välttämiseksi.

5.1 CPU: n asentaminen

1. Locate the LGA2011 V3 CPU socket on the motherboard.
2. Gently push down the CPU retention lever and swing it open.
3. Align the triangular mark on your CPU with the corresponding mark on the socket. Carefully place the CPU into the socket without forcing it.
4. Sulje kiinnitysvipu kiinnittääksesi suorittimen.
5. Levitä ohut, tasainen kerros lämpötahnaa suorittimen päälle.
6. Install the CPU cooler according to its manufacturer's instructions, ensuring proper contact and pressure.

Kuva 5.1: Lähikuva view of the LGA2011 V3 CPU socket on the motherboard, ready for CPU installation.

5.2 Installing RAM Modules

1. Avaa DDR3-muistipaikkojen molemmissa päissä olevat pidikkeet.
2. Kohdista RAM-moduulin lovi muistipaikan kiilaan.
3. Paina RAM-moduulin molempia päitä lujasti alas, kunnes klipsit napsahtavat paikoilleen ja kiinnittävät moduulin.
4. For optimal performance, install RAM modules in matching pairs across the four channels as indicated in the motherboard manual or silkscreen.

Kuva 5.2: View of the eight DDR3 RAM slots on the motherboard, showing their arrangement for quad-channel memory configuration.

5.3 Installing Storage Devices (M.2 NVME & SATA)

1. M.2 NVME SSD: Locate the M.2 slot. Insert the M.2 SSD at an angle into the slot, then gently push it down and secure it with the provided screw.
2. SATA-asemat: Connect your SATA SSDs or HDDs to the SATA 3.0 ports using SATA data cables. Ensure the power supply SATA power connectors are also attached to the drives.

Figure 5.3: Close-up of the M.2 interface on the motherboard, highlighting its position and the PCI-E Gen3 X4 connection for high-speed data transfer.

Kuva 5.4: View of the eight orange SATA 3.0 ports on the motherboard, providing ample connectivity for storage devices.

5.4 Virtalähteen liittäminen

1. Connect the 24-pin ATX power connector from your power supply unit (PSU) to the corresponding port on the motherboard.
2. Connect the 8-pin CPU power connector (EPS12V) from your PSU to the 8-pin port near the CPU socket.

5.5 Installing Expansion Cards (PCIe)

1. Locate the desired PCI-E 3.0 x16 or x1 slots.
2. Irrota vastaava laajennuspaikan kansi tietokoneen kotelosta.
3. Align the expansion card with the slot and press down firmly until it is fully seated. Secure the card with a screw to the case.

Kuva 5.5: Kulmassa view of the motherboard, highlighting the three PCI Express 3.0 x16 slots and the smaller PCIe x1 slots, ready for graphics cards and other expansion cards.

6. Emolevyn käyttö

6.1 Ensimmäinen käynnistys ja BIOS-asetukset

1. Kun olet koonnut kaikki osat, kytke näyttö, näppäimistö ja hiiri.
2. Power on your system. During the initial boot sequence, repeatedly press the DEL or F2 key (common for JINGSHA motherboards) to enter the BIOS/UEFI setup utility.
3. Tarkista BIOSissa, että kaikki asennetut komponentit (suoritin, RAM, tallennustila) tunnistetaan oikein.
4. Määritä käynnistysjärjestys priorisoidaksesi käyttöjärjestelmän asennusmedian (USB-asema tai DVD).
5. Tallenna muutokset ja poistu BIOSista. Järjestelmä käynnistyy uudelleen.

6.2 Käyttöjärjestelmän asennus

Follow the instructions provided with your operating system (e.g., Windows, Linux) to complete the installation process. Ensure you install all necessary drivers for the motherboard's chipsets, network, audio, and other components from the manufacturer's website or included driver disc.

7. Huolto

Oikea huolto varmistaa emolevyn pitkän käyttöiän ja vakaan toiminnan.

• Pölynpoisto: Puhdista emolevy ja komponentit säännöllisesti pölystä paineilmalla. Varmista, että järjestelmä on sammutettu ja irrotettu pistorasiasta ennen puhdistamista.
• BIOS-päivitykset: Periodically check the Docooler or JINGSHA official website for BIOS updates. BIOS updates can improve compatibility, stability, and performance. Follow update instructions carefully to avoid damaging the motherboard.
• Ohjaimen päivitykset: Pidä järjestelmäohjaimet ajan tasalla varmistaaksesi optimaalisen suorituskyvyn ja yhteensopivuuden uusien ohjelmistojen ja laitteistojen kanssa.
• Ympäristöolosuhteet: Operate the motherboard in a well-ventilated environment with stable temperature and humidity to prevent overheating and component degradation.

8. Vianmääritys

Tässä osiossa käsitellään yleisiä ongelmia, joita saatat kohdata.

8.1 Ei virtaa / Ei käynnistystä

• Ensure the 24-pin ATX and 8-pin CPU power connectors are securely plugged into the motherboard.
• Check if the power supply unit (PSU) is switched on and connected to a working power outlet.
• Verify that the front panel power button cable is correctly connected to the motherboard's header.

8.2 Ei näyttöä

• Ensure your graphics card (if dedicated) is properly seated in its PCI-E slot and has all necessary power cables connected.
• Check that your monitor cable is securely connected to the graphics card or motherboard (if integrated graphics are used, though X99 typically requires a dedicated GPU).
• Try reseating your RAM modules. Incorrectly seated RAM is a common cause of no display.

8.3 POST Code Display (Digital Diagnostic Card)

The motherboard is equipped with a digital diagnostic card (POST code display) that shows a two-digit code during boot-up. Refer to the motherboard's detailed technical documentation (often available on the manufacturer's website) for a list of POST codes and their meanings. This can help pinpoint the exact component causing a boot failure.

Kuva 8.1: Lähikuva view showing the integrated digital diagnostic card (POST code display) on the motherboard, which assists in identifying hardware issues during boot.

9. Takuu ja tuki

For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Docooler or JINGSHA websivusto. Säilytä ostokuitti takuuvaatimuksia varten.