1. Johdanto
The Selec CH-403-2 is a precision temperature chiller controller designed for industrial and commercial applications requiring accurate temperature regulation. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your device. Please read this manual thoroughly before installation and operation.
2. Turvallisuustiedot
Noudata aina seuraavia turvaohjeita loukkaantumisten ja laitteen vaurioitumisen välttämiseksi:
- Varmista, että virtalähde on irrotettu ennen johdotuksen tai huollon suorittamista.
- Asennuksen ja huollon saa suorittaa vain pätevä henkilöstö.
- Varmista, että virtalähde voltage vastaa ohjaimen teknisiä tietoja.
- Älä altista ohjainta liialliselle kosteudelle, pölylle tai syövyttäville kaasuille.
- Varmista oikea maadoitus sähköiskun välttämiseksi.
3. Asennus
3.1 Pakkauksesta purkaminen
Carefully remove the controller from its packaging. Inspect the device for any signs of damage during transit. Report any damage to your supplier immediately.
3.2 Asennus
The CH-403-2 is designed for panel mounting. Cut an opening of 45mm x 45mm (1.77" x 1.77") in the panel. Insert the controller into the opening and secure it using the provided mounting clamps. Ensure a snug fit to prevent dust and moisture ingress.
3.3 Johdotusliitännät
Refer to the wiring diagram located on the side of the controller or in the detailed technical specifications. Ensure all connections are secure and correct before applying power.
- Virtalähde: Connect the appropriate AC voltage (e.g., 230V AC) to the designated power terminals.
- Anturin tulo: Connect the temperature sensor (e.g., NTC, PT100) to the sensor input terminals. Observe polarity if applicable.
- Ohjauslähtö: Connect the chiller or heating element to the relay output terminals. Ensure the load current does not exceed the relay's maximum rating.
- Hälytyslähtö (valinnainen): If applicable, connect external alarm devices to the alarm output terminals.
3.4 Ensimmäinen käynnistys
After all connections are verified, apply power to the controller. The display should illuminate, showing the current temperature and default settings.
4. Käyttö
4.1 Näytön loppuview
The front panel features a digital display showing the process value (PV) and set point (SV), along with indicator LEDs for output status (e.g., ON/OFF, Alarm).
4.2 Painikkeiden toiminnot
- SET -painike: Käytetään parametrien asetustilaan siirtymiseen ja valintojen vahvistamiseen.
- YLÖS/ALAS-painikkeet: Used to navigate through parameters and adjust values.
- MODE-painike: Used to switch between display modes or access advanced settings.
4.3 Setting Temperature Setpoint (SV)
- Paina SARJA button once. The SV value will flash.
- Käytä UP or ALAS buttons to adjust the setpoint to the desired temperature.
- Paina SARJA button again to confirm the new setpoint. The display will return to showing the PV.
4.4 Parametrien konfigurointi
To access advanced parameters such as hysteresis, calibration offset, or delay times, press and hold the SARJA button for several seconds until the first parameter code appears. Use the YLÖS/ALAS buttons to navigate through parameters and the SARJA button to select and modify values. Refer to the detailed parameter list in the full technical manual for specific codes and ranges.
5. Huolto
5.1 Puhdistus
Clean the front panel of the controller periodically with a soft, damp liinaa. Älä käytä hankaavia puhdistusaineita tai liuottimia, sillä ne voivat vahingoittaa näyttöä taiasing. Ensure no liquid enters the device.
5.2 Säännölliset tarkastukset
- Tarkista johtojen liitännät löysyyden tai korroosion varalta.
- Verify the temperature sensor is clean and properly installed.
- Check for any unusual noises or smells from the controller or connected equipment.
5.3 Kalibrointi
If temperature readings appear inaccurate, the sensor or controller may require calibration. Refer to the advanced parameter settings for sensor offset adjustment. For precise calibration, consult a qualified technician.
6. Vianmääritys
Tässä osiossa käsitellään yleisiä ongelmia, joita saatat kohdata. Ongelmissa, joita ei ole lueteltu tässä, ota yhteyttä tekniseen tukeen.
| Ongelma | Mahdollinen syy | Ratkaisu |
|---|---|---|
| No display / Power off | Ei virtaa; Väärä johdotus; Palanut sulake | Check power connections; Verify voltage; Replace fuse if necessary. |
| Väärä lämpötilalukema | Sensor faulty; Sensor wiring incorrect; Calibration offset needed | Check sensor connections; Replace sensor; Adjust calibration offset in parameters. |
| Lähtö ei vaihdu | Setpoint not reached; Hysteresis setting too wide; Output relay faulty | Verify setpoint and current temperature; Adjust hysteresis; Test output relay (by qualified personnel). |
| Error Code 'E1' | Anturin avoin piiri | Check sensor wiring for breaks; Replace sensor. |
| Error Code 'E2' | Anturin oikosulku | Check sensor wiring for shorts; Replace sensor. |
7. Tekniset tiedot
| Parametri | Arvo |
|---|---|
| Malli | CH-403-2 |
| Syöttötyyppi | NTC / PT100 (selectable) |
| Lämpötila-alue | -50°C to 150°C (sensor dependent) |
| Ohjauslähtö | 1 x Relay (NO/NC), 5A @ 250V AC resistive |
| Apulähtö | 1 x Relay (NO), 3A @ 250V AC resistive (Alarm) |
| Supply Voltage | 230V AC ±10%, 50/60 Hz |
| Tarkkuus | ±1% of full scale ±1 digit |
| Näyttö | 3-numeroinen LED |
| Asennus | Panel Mount (45x45mm cutout) |
| Käyttölämpötila | 0 °C - 50 °C |
| Mitat (LxKxS) | 48mm x 48mm x 85mm |
8. Takuu ja tuki
Selec products are covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Selec website. For technical support, service, or spare parts, please contact your authorized Selec distributor or customer service department, providing your product model number (CH-403-2) and serial number.