1. Johdanto
This manual provides instructions for the safe and efficient operation, setup, and maintenance of your SOMMER Pearl 4018 4018V000 TX55-868-4 garage door remote control. This device utilizes the SOMloq2 radio system and is compatible with Somloq Rollingcode systems, as well as Pro Teckentrup Drive models 4020, 4026, and 4031 Slider.
Kuva 1: SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control. This image shows the compact, modern design of the remote control, featuring four buttons and a stainless steel application.
2. Turvallisuustiedot
- Keep the remote control out of reach of children to prevent accidental operation of the garage door.
- Älä anna lasten leikkiä kaukosäätimellä tai autotallin ovenavaajalla.
- Varmista ennen käyttöä, että autotallin ovi on näkyvissä eikä sen edessä ole esteitä.
- Do not operate the garage door if people or objects are in its path.
- Hävitä paristot paikallisten määräysten mukaisesti. Älä polta paristoja.
- Avoid exposing the remote control to extreme temperatures, moisture, or direct sunlight.
3. Pakkauksen sisältö
Varmista, että pakkauksessasi on kaikki tarvittavat osat:
- SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control (quantity as purchased, typically 2 units)
- 3V CR2032 Lithium-metal battery (pre-installed or included)
4. Asennus ja ohjelmointi
The SOMMER Pearl 4018 remote control must be programmed to your garage door opener receiver. The exact programming steps may vary slightly depending on your specific SOMMER garage door opener model. Refer to your garage door opener's manual for precise instructions. A common programming method is outlined below:
- Paikanna vastaanotin: Identify the garage door opener's motor unit. On the motor unit, locate the "Learn" or "Program" button. This button is often small and may be recessed.
- Aktivoi oppimistila: Press and immediately release the "Learn" or "Program" button on your garage door opener. The indicator light on the opener will typically illuminate or flash, indicating it is in learn mode. You usually have about 30 seconds to complete the next step.
- Kaukosäätimen ohjelmointi: Within the learn mode timeframe, press and hold the desired button on your SOMMER Pearl 4018 remote control that you wish to use for operating the garage door.
- Vahvista ohjelmointi: Release the button on the remote control once the garage door opener's indicator light flashes or changes color, or if the garage door moves slightly. This indicates successful programming.
- Testitoiminta: Paina kaukosäätimen ohjelmoitua painiketta varmistaaksesi, että autotallin ovi toimii oikein.
- Program Additional Remotes: Repeat these steps for any additional SOMMER Pearl 4018 remote controls you wish to program.
Note: If your garage door opener has a different programming procedure (e.g., using a master remote or a specific sequence), please consult your opener's manual.
5. Käyttöohjeet
Once programmed, operating your SOMMER Pearl 4018 remote control is straightforward:
- Oven avaaminen/sulkeminen: Press the programmed button on your remote control once. The garage door will begin to open or close.
- Oven pysäyttäminen: Press the same programmed button again while the door is in motion to stop it.
- Useita ovia: If you have programmed multiple garage doors to different buttons on your remote, press the corresponding button for the desired door.
- Alue: The remote control has an approximate range of 50-140 meters, depending on environmental conditions and obstructions.
6. Huolto
6.1. Pariston vaihto
The SOMMER Pearl 4018 remote control uses a 3V CR2032 Lithium-metal battery. When the remote's range decreases significantly or it stops responding, it is likely time to replace the battery.
- Avaa Casing: Avaa kaukosäätimen c varovastiasing. This usually involves prying it open with a small flat-head screwdriver or a similar tool at a designated notch.
- Irrota vanha akku: Note the orientation of the old CR2032 battery (positive (+) side up or down). Gently remove the old battery.
- Aseta uusi paristo: Insert a new 3V CR2032 Lithium-metal battery, ensuring the correct polarity. The positive (+) side typically faces upwards.
- Sulje Casing: Napsauta kaukosäädin c:täasing takaisin yhteen tukevasti.
- Testata: Test the remote control to ensure it functions correctly with the new battery.
6.2. Puhdistus
Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or allow moisture to enter the casing.
7. Vianmääritys
| Ongelma | Mahdollinen syy | Ratkaisu |
|---|---|---|
| Kaukosäädin ei toimi. | Akku on tyhjä tai virta vähissä. | Vaihda CR2032-paristo (katso kohta 6.1). |
| Kaukosäädin ei toimi. | Remote is not programmed or programming was lost. | Reprogram the remote control to your garage door opener (see Section 4). |
| Lyhennetty toimintasäde. | Akku vähissä. | Vaihda CR2032-paristo (katso kohta 6.1). |
| Lyhennetty toimintasäde. | Radio interference or obstructions. | Ensure there are no large metal objects or other radio-emitting devices between the remote and the receiver. Try operating from a different position. |
| Garage door opener not responding to remote. | Garage door opener is unplugged or has no power. | Check the power supply to your garage door opener. |
8. Tekniset tiedot
- Malli: Pearl 4018 4018V000 TX55-868-4
- Radiojärjestelmä: SOMloq2
- Painikkeet: 4
- Radiotaajuus: FM 868.8 MHz, FM 868.95 MHz
- Alue: Noin 50–140 metriä (ympäristöstä riippuen)
- Mitat: 79 x 26 x 13 mm (3.11 x 1.02 x 0.51 tuumaa)
- Akun tyyppi: 3V CR2032 Lithium-metal
- Paino: 40 g (1.41 unssia)
- Yhteensopivuus: Somloq Rollingcode system, Pro Teckentrup Drive (compatible with 4020, 4026, 4031 Slider)
9. Takuu ja tuki
For warranty information and technical support, please refer to the documentation provided with your original purchase or contact SOMMER customer service directly. Contact details can typically be found on the manufacturer's official websivusto.