Nerf Modulus Ghost Ops Shadow ICS-6 käyttöohje

Tärkeitä turvallisuustietoja

WARNING: CHOKING HAZARD - Small parts may be generated. Not for children under 3 years.

Do not aim at eyes or face. Use only official NERF darts. Other darts may not meet safety standards. Do not modify darts or blaster.

Aikuisen valvontaa suositellaan käytön aikana.

1. Asennus

1.1 Pakkauksesta purkaminen

Carefully remove all components from the packaging. Ensure all parts listed in the 'What's in the Box' section are present.

• Blaster
• Tynnyrin jatkopala
• 6 Darts
• Ohjeet

Image 1.1: The Nerf Modulus Ghost Ops Shadow ICS-6 blaster and its components as seen in the retail packaging.

1.2 Akun asennus

The blaster requires 3 AAA alkaline batteries for the illumination feature. Demo batteries are included.

1. Paikanna blasterin paristolokero.
2. Kierrä paristolokeron kansi auki ristipääruuvimeisselillä (ei sisälly toimitukseen).
3. Aseta 3 uutta AAA-alkaliparistoa paikoilleen varmistaen oikea napaisuus (+/-).
4. Aseta paristolokeron kansi takaisin paikalleen ja kiinnitä se ruuvilla.

Image 1.2: The blaster's battery requirement for its illumination feature.

1.3 Assembling the Blaster

The Illuminator Barrel can be attached to the front of the blaster.

1. Align the barrel extension with the front attachment point of the blaster.
2. Push the barrel extension firmly until it clicks into place.
3. To remove, press the release button (if present) or pull the barrel extension off.

Image 1.3: Attaching the illuminator barrel to customize the blaster.

Image 1.4: Detaching the illuminator barrel from the blaster.

2. Blasterin käyttö

2.1 Tikanheittojen lataaminen

The Shadow ICS-6 blaster features a breech-load design with an internal clip system that holds up to 6 darts.

1. Open the breech by pulling back the priming handle.
2. Insert one dart at a time into the internal clip system. Ensure darts are fully seated.
3. Close the breech by pushing the priming handle forward until it locks.

Image 2.1: Loading a dart into the blaster's internal clip system.

Kuva 2.2: Yksityiskohtainen view of dart loading.

2.2 Blasterin laukaiseminen

Once darts are loaded and the blaster is primed:

1. Aim the blaster at a safe target.
2. Vedä liipaisinta ampuaksesi yhden tikan.
3. To fire another dart, repeat the loading and priming steps.

Image 2.3: The blaster and included darts.

2.3 Illumination Feature

The blaster features a clear housing that illuminates when the light activator is pressed. This allows for both stealth and illuminated modes.

• Stealth-tila: Keep the blaster clear (lights off) for discreet action.
• Illuminated Mode: Press the light activator button to illuminate the blaster, useful for low-light environments. The attached Illuminator Barrel will also light up.

Image 2.4: The blaster in illuminated mode.

Image 2.5: The blaster in clear, stealth mode.

Image 2.6: The illuminator barrel glowing when attached.

3. Huolto

3.1 Yleishoito

• Keep the blaster clean by wiping it with a dry cloth. Do not use harsh chemicals or immerse in water.
• Säilytä puhallin viileässä, kuivassa paikassa, poissa suorasta auringonvalosta.
• Remove batteries if the blaster will not be used for an extended period to prevent leakage.

3.2 Tikanheiton hoito

• Use only official Nerf darts to ensure optimal performance and safety.
• Inspect darts for damage before use. Damaged darts can affect performance and potentially jam the blaster.
• Do not modify darts.

4. Vianmääritys

5. Tekniset tiedot