SMT-ultraäänihomogenisaattori UH-50 Käyttöohje

1. Johdanto

This manual provides essential information for the safe and efficient operation of the SMT Ultrasonic Homogenizer UH-50. Please read this manual thoroughly before using the device and keep it for future reference.

The SMT Ultrasonic Homogenizer UH-50 is a compact and lightweight device designed for laboratory applications requiring ultrasonic homogenization. Its key features include a space-saving design, a lightweight vibrator (approximately 160g), and a hand pulser for convenient control of ultrasonic vibration. The system automatically adjusts output to maintain a constant amplitude, adapting to variations in sample load and pressure.

2. Turvallisuustiedot

WARNING: This is a professional-use product. It should only be operated by trained personnel in a laboratory setting.

• No Dry Operation: Do not operate the ultrasonic vibrator without it being immersed in a liquid sample. Dry operation can cause damage to the device.
• Varmista, että laite on asetettu vakaalle ja tasaiselle alustalle.
• Connect the device to a grounded power outlet with the specified voltage (AC100V, 50/60Hz).
• Avoid direct contact with the vibrating tip during operation.
• Älä pura tai yritä korjata laitetta itse. Ota yhteyttä pätevään huoltohenkilöstöön.
• Keep the unit away from flammable materials and excessive moisture.

3. Tuotteen osat ja hallintalaitteet

The SMT Ultrasonic Homogenizer UH-50 consists of a main control unit and an ultrasonic vibrator with a hand pulser. Familiarize yourself with the components and controls shown below.

Figure 1: SMT Ultrasonic Homogenizer UH-50 Overview
This image displays the main control unit of the SMT Ultrasonic Homogenizer UH-50 on the left, connected to the ultrasonic vibrator on the right. The control unit features a "MONITOR" display, a "POWER" switch, "CONSTANT" and "HAND" mode selector, "TUNE" and "OUTPUT" adjustment knobs. A yellow label on top of the main unit warns against dry operation. The vibrator is a slender, metallic component with a tip.

Ohjauspaneelin kuvaus:

• Virtakytkin: Kytkee laitteen päälle ja pois päältä.
• MONITOR Display: Shows the current output level or other operational parameters.
• CONSTANT/HAND Selector:
  • VAKIO: Continuous ultrasonic operation.
  • KÄSI: Operation controlled by the hand pulser switch.
• VIRITYS-nuppi: Adjusts the ultrasonic frequency for optimal performance.
• OUTPUT-nuppi: Controls the ultrasonic power output (amplitude).
• Hand Pulser: A switch located on the vibrator cable for convenient start/stop of ultrasonic vibration when in HAND mode.

4. Asennus

1. Purkaminen: Poista kaikki osat varovasti pakkauksesta. Varmista, että kaikki osat ovat mukana pakkauslistan mukaisesti.
2. Sijoitus: Place the main control unit on a stable, flat, and dry surface, ensuring adequate ventilation around the unit.
3. Yhdistä vibraattori: Connect the ultrasonic vibrator cable securely to the designated port on the main control unit.
4. Virtaliitäntä: Ensure the POWER switch is in the "OFF" position. Connect the power cord to the main control unit and then to a grounded AC100V, 50/60Hz power outlet.
5. Alkutarkastus: Before first use, visually inspect the vibrator tip for any damage or wear.

5. Käyttöohjeet

Always ensure the vibrator tip is immersed in the sample liquid before starting operation to prevent damage from dry running.

1. Valmista Sampseuraavat: Aseta sample in an appropriate vessel. Ensure the vessel is suitable for ultrasonic treatment and can withstand the energy generated.
2. Immerse Vibrator: Carefully immerse the tip of the ultrasonic vibrator into the sample liquid. Ensure the tip is sufficiently submerged but not touching the bottom or sides of the vessel.
3. Virta päälle: Turn the POWER switch to the "ON" position. The MONITOR display should illuminate.
4. Valitse tila:
   • For continuous operation, set the selector to "CONSTANT".
   • For intermittent operation controlled by the hand pulser, set the selector to "HAND".
5. Adjust TUNE: Slowly adjust the TUNE knob until the MONITOR display shows the highest stable reading, indicating optimal resonance.
6. Set OUTPUT: Adjust the OUTPUT knob to the desired ultrasonic power level. The system will automatically control the output to maintain a constant ampleveyttä.
7. Start Homogenization:
   • In "CONSTANT" mode, homogenization will start immediately.
   • In "HAND" mode, press and hold the switch on the hand pulser to start homogenization. Release the switch to stop.
8. Valvontaprosessi: Observe the homogenization process. Adjust OUTPUT or TUNE as necessary.
9. Valmistuminen: Once homogenization is complete, turn the OUTPUT knob to minimum, then turn the POWER switch to "OFF".
10. Clean Vibrator: Carefully remove the vibrator from the sample and clean it immediately according to the maintenance instructions.

6. Huolto

Regular maintenance ensures the longevity and optimal performance of your SMT Ultrasonic Homogenizer UH-50.

• Cleaning the Vibrator Tip: After each use, thoroughly clean the vibrator tip to prevent sample residue buildup. Use appropriate cleaning agents for the materials being processed. Rinse with distilled water and dry completely.
• Pääyksikön puhdistus: Wipe the exterior of the main control unit with a soft, damp cloth. Do not use abrasive cleaners or allow liquids to enter the unit.
• Tarkastus: Periodically inspect the vibrator tip, cable, and connectors for any signs of wear, damage, or corrosion. Replace damaged parts immediately.
• Varastointi: Säilytä laitetta puhtaassa ja kuivassa paikassa, kun sitä ei käytetä.

7. Vianmääritys

If you encounter issues with your SMT Ultrasonic Homogenizer UH-50, refer to the following common problems and solutions:

• Ei virtaa:
  • Tarkista, että virtajohto on kytketty kunnolla sekä laitteeseen että pistorasiaan.
  • Varmista, että pistorasia on toimiva.
  • Verify the POWER switch is in the "ON" position.
• Ei ultraäänivärähtelyä:
  • Ensure the vibrator tip is properly immersed in liquid.
  • Check the TUNE and OUTPUT knob settings. Adjust TUNE for optimal resonance.
  • If in "HAND" mode, ensure the hand pulser switch is pressed.
  • Inspect the vibrator cable for damage.
• Matala tai epäjohdonmukainen tulos:
  • Adjust the TUNE knob to find the optimal frequency.
  • Increase the OUTPUT knob setting.
  • Ensure the vibrator tip is clean and free of damage.
  • Tarkista sample volume and viscosity are within appropriate limits for the device.

If the problem persists after attempting these solutions, please contact SMT customer support or your local distributor for assistance.

8. Tekniset tiedot

9. Takuu ja tuki

Specific warranty information for the SMT Ultrasonic Homogenizer UH-50 is not provided in this document. Please refer to your purchase agreement or contact your local SMT distributor for details regarding warranty coverage and technical support.

Lisätietoja saat myös osoitteesta SMT Brand Store on Amazon.co.jp.