PLUS 58-437

PLUS 58-437 IS-009NQ Seal Name Cube Instruction Manual

Malli: 58-437

1. Johdanto

This manual provides instructions for the proper use and maintenance of your PLUS 58-437 IS-009NQ Seal Name Cube. Please read this manual thoroughly before using the product to ensure optimal performance and longevity.

PLUS 58-437 IS-009NQ Seal Name Cube in black

Image 1.1: The PLUS 58-437 IS-009NQ Seal Name Cube in black.

2. Tuote ohiview

The PLUS 58-437 IS-009NQ Seal Name Cube is a self-inking stamp designed for ease of use and consistent impressions. Its unique square body prevents rolling and assists in precise alignment.

Tärkeimmät ominaisuudet:

  • Square Body Design: Prevents the stamp from rolling when placed on a desk or in a drawer, and keeps the cap secure when removed during use.
  • Straight Impression: The square shape allows for easy alignment with document grids or ruled lines, ensuring straight and accurate stamping.
  • Suuri kapasiteetti: Provides approximately 3,000 continuous impressions before needing an ink cartridge replacement.
  • Replaceable Ink Cartridge: Designed for easy and mess-free ink cartridge replacement, making the stamp reusable and economical.
  • Musteen väri: Vermilion (oil-based pigment ink).
Dimensions of the PLUS Seal Name Cube: 18mm width, 18mm depth, 70mm height

Image 2.1: Product dimensions of the Seal Name Cube (18mm x 18mm x 70mm).

PLUS Seal Name Cube lying on its side, demonstrating its non-rolling square design

Image 2.2: The square body prevents the stamp from rolling.

3. Asennus

The PLUS 58-437 IS-009NQ Seal Name Cube comes pre-inked and ready for immediate use. No initial setup or assembly is required.

  1. Poista suojakorkki st:stäamp.
  2. Place the cap aside. Its square design will prevent it from rolling.

4. Käyttöohjeet

Follow these steps to achieve clear and straight impressions:

  1. Paikannus: Pidä kiinniamp firmly. Align the square body of the stamp with the grid lines or ruled sections of your document. This helps ensure a perfectly straight impression.
  2. Stamping: Paina stamp down firmly and evenly onto the desired surface. Apply consistent pressure to ensure the entire impression surface makes contact.
  3. Julkaisu: Nosta stamp straight up to avoid smudging.
  4. Kertaus: After use, replace the protective cap to prevent the ink from drying out.

Important Note: This product is designed for general stamping purposes and should not be used for official seals or documents requiring legal authentication.

Comparison showing how the square PLUS Name Cube helps stamp straight compared to a round stamp

Image 4.1: The square body design facilitates straight and accurate stamping.

Close-up of the stamp impression, showing a 9mm diameter

Image 4.2: The impression surface has a diameter of 9mm.

5. Huolto

Mustepatruunan vaihto:

When the impression starts to fade, it is time to replace the ink cartridge. The PLUS 58-437 IS-009NQ uses a replaceable ink cartridge system for convenience and extended product life.

  1. Tunnista kasetti: The ink cartridge is located inside the stamp kehon.
  2. Poista vanha kasetti: Carefully separate the stamp body to access the old cartridge. Gently pull out the used cartridge.
  3. Aseta uusi kasetti: Insert a new, compatible PLUS ink cartridge (sold separately) into the designated slot. Ensure it clicks securely into place.
  4. Kokoa uudelleen: Reassemble the stamp kehon.

Note: Always use genuine PLUS replacement ink cartridges to ensure proper function and ink quality.

Diagram showing how to replace the ink cartridge in the PLUS Seal Name Cube

Image 5.1: Illustration of the ink cartridge replacement process.

6. Vianmääritys

OngelmaMahdollinen syyRatkaisu
Faint or incomplete impressionsInk cartridge is running low or dry.Replace the ink cartridge (refer to Section 5).
Smudged impressionsStamp was not lifted straight up, or moved during impression.Ensure to press firmly and lift the stamp straight up without lateral movement.

7. Tekniset tiedot

  • Malli: 58-437 IS-009NQ
  • Merkki: PLUS
  • Ulkoiset mitat: 18mm (W) x 18mm (D) x 70mm (H)
  • Impression Surface Diameter: 9 mm
  • Mustetyyppi: Oil-based pigment ink
  • Musteen väri: Kirkkaanpunainen
  • Approximate Impressions per Cartridge: 3,000
  • Patruunan tyyppi: Vaihdettavissa

8. Takuu ja tuki

For warranty information or technical support, please contact the manufacturer, PLUS, directly. Refer to the product packaging or the official PLUS websivustolta löydät alueesi yhteystiedot ja takuuehdot.

Valmistaja: PLUS (プラス)

Websivusto: www.plus.co.jp (This is a general link, specific support links may vary by region)

© 2023 PLUS Corporation. All rights reserved.