National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light Manual

Johdanto

This manual provides detailed instructions for the installation, operation, and maintenance of your National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light. Please read all instructions carefully before beginning installation and retain this manual for future reference.

Tärkeitä turvallisuusohjeita

• Lue kaikki ohjeet: Ensure you understand all steps before installation or operation.
• Vain sisäkäyttöön: This fixture is designed for dry, indoor locations. Do not install in wet or damp ympäristöissä.
• Katkaise virta: Always disconnect power at the circuit breaker before installing, servicing, or replacing bulbs.
• Pätevä sähköasentaja: Installation should be performed by a qualified electrician or a person familiar with electrical wiring.
• Oikea maadoitus: Varmista, että valaisin on maadoitettu asianmukaisesti sähköiskun välttämiseksi.
• Voitage: This fixture operates on 120V AC input, converting to 12V for the Xenon bulb.
• Polttimon tyyppi: Use only the specified 18W T5 Wedge 12V Xenon bulb.

Pakkauksen sisältö

Varmista, että kaikki osat ovat mukana ennen asennuksen aloittamista:

• XTL-1-HW/WH Under Cabinet Light Fixture (1)
• 18W T5 Wedge 12V Xenon Bulb (1)
• Push-in Connectors (for wiring)
• Kiinnitystarvikkeet (ruuvit)
• Käyttöohje (tämä asiakirja)

Asennus ja asennus

Tarvittavat työkalut

• Ruuvimeisseli (Phillips ja/tai litteäpäinen)
• Langanpoistajat
• Drill (if pre-drilling pilot holes)
• Lyijykynä
• Mittanauha

Valaisimen asennus

1. Katkaise virta: Locate the circuit breaker controlling the area where the light will be installed and turn off the power. Verify power is off using a voltage testaaja.
2. Määritä sijainti: Choose a suitable location under a cabinet, ensuring adequate clearance and access for wiring. The fixture dimensions are 9" L x 4.63" W x 1.25" H.
3. Mark mounting points: Hold the fixture in the desired position and mark the mounting screw locations with a pencil.
4. Kiinnitys: Using the provided mounting screws, attach the fixture securely to the underside of the cabinet.

Electrical Connection (Hardwire)

1. Valmistele johdotus: Route the 120V AC supply wires to the fixture's wiring compartment. Strip approximately 1/2 inch of insulation from the ends of the supply wires (black, white, ground).
2. Kytke johdot: Use the provided push-in connectors to connect the fixture's wires to the supply wires:
   • Yhdistä musta (hot) wire from the supply to the musta kiinnittimen johto.
   • Yhdistä valkoinen (neutral) wire from the supply to the valkoinen kiinnittimen johto.
   • Yhdistä vihreä (ground) wire from the supply to the vihreä or bare copper wire of the fixture.
3. Secure connections: Ensure all connections are tight and secure. Tuck wires neatly into the wiring compartment.
4. Install bulb: Gently insert the 18W T5 Wedge 12V Xenon bulb into the fixture's socket. Avoid touching the glass portion of the bulb with bare hands.
5. Close diffuser: Close the frosted glass diffuser lens. It features a simple hinged push-to-open mechanism.
6. Palauta virta: Kytke virta takaisin katkaisijasta.

Kuva 1: Yliview of the National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light, showing its compact design and key dimensions (Length: 9 inches, Width: 4.63 inches, Height: 1.25 inches). The image also highlights the frosted glass diffuser and the integrated hi-lo dimmer switch.

Valon käyttäminen

The XTL-1-HW/WH fixture is equipped with an integrated hi-lo dimmer switch for adjustable light output.

• Kytkeminen päälle: Press the switch to the 'ON' position.
• Kirkkauden säätäminen: The switch typically has a 'HI' and 'LO' setting. Select the desired brightness level.
• Sammuta: Press the switch to the 'OFF' position.

Huolto

Polttimon vaihto

The Xenon bulb has an average life of 10,000 hours. When replacement is necessary:

1. Katkaise virta: Disconnect power to the fixture at the circuit breaker.
2. Open diffuser: Gently push the hinged frosted glass diffuser to open it. No tools are required.
3. Irrota vanha lamppu: Carefully pull the old 18W T5 Wedge 12V Xenon bulb straight out of its socket.
4. Asenna uusi lamppu: Insert a new 18W T5 Wedge 12V Xenon bulb into the socket. Avoid touching the glass with bare hands; use a clean cloth or gloves if necessary.
5. Close diffuser: Close the frosted glass diffuser until it latches securely.
6. Palauta virta: Kytke virta takaisin katkaisijasta.

Puhdistus

To clean the fixture, ensure power is off. Wipe the exterior surfaces with a soft, dry cloth. For stubborn marks, a slightly damp cloth may be used, followed by drying. Do not use abrasive cleaners or solvents.

Vianetsintä

Tuotteen tekniset tiedot

Takuu ja asiakastuki

For warranty information or technical assistance, please contact National Specialty Lighting customer support. Keep your purchase receipt as proof of purchase.

Yhteystiedot löytyvät yleensä valmistajan viralliselta verkkosivulta. websivustolla tai tuotepakkauksessa.