SWIMLINE HYDROTOOLS 12-Inch Sand Filter System Instruction Manual

1. Johdanto

This manual provides instructions for the installation, operation, and maintenance of your SWIMLINE HYDROTOOLS 12-inch Sand Filter System, Model 71225. This system is designed for above-ground pools up to 8,000 gallons, offering efficient water filtration to maintain clear and clean pool water. It features a durable 12-inch tank, a 0.3 THP single-speed pump with a 1,980 GPH flow rate, and a versatile 4-way multi-port valve.

Figure 1: SWIMLINE HYDROTOOLS 12-inch Sand Filter System.

The system is engineered for optimized filtration, consistent performance, and efficient backwashing, ensuring the cleanest water quality for your pool. The pump operates at low noise levels and is DOE compliant.

2. Turvallisuustiedot

Read and understand all instructions before installing or operating this product. Failure to follow these instructions can result in serious injury or death.

• Sähköturvallisuus: Always disconnect power to the pump before performing any service or maintenance. Ensure the power cord is connected to a grounded outlet with Ground Fault Circuit Interrupter (GFCI) protection. Do not use extension cords.
• Vesi- ja kemikaaliturvallisuus: Do not operate the pump dry. Ensure the pump is filled with water before starting. Keep all pool chemicals away from the filter system components.
• Paineturvallisuus: Do not operate the filter system if any part is damaged or if the pressure gauge indicates excessive pressure. Never attempt to open the filter tank or multi-port valve while the system is operating under pressure.
• Lapset: Keep children away from the filter system during operation and maintenance.
• Asennus: Install the filter system on a level, solid surface. Ensure adequate drainage around the unit.

3. Järjestelmän komponentit

Your SWIMLINE HYDROTOOLS sand filter system comes as a complete combo, including all necessary hardware for assembly and operation. Verify that all components are present before beginning installation.

• Filter Tank (12-inch, double reinforced)
• Single Speed Pump (0.3 THP, Model 71206)
• Suodatinpohja
• 4-tieinen moniporttiventtiili
• Painemittari
• 3-Prong Plug & Power Cord
• Connection Hoses (2 included)
• Letkuadapterit ja Clamps
• Tyhjennystulppa

Figure 2: Included accessories for the filter system.

Figure 3: Key components of the complete system.

4. Asennusohjeet

Proper setup is crucial for optimal performance. Follow these steps carefully.

4.1 Preparing the Filter Tank

1. Place the filter base on a firm, level surface near your pool.
2. Position the filter tank onto the base.
3. Carefully add filter sand (not included) into the tank. The 12-inch tank has a capacity of up to 42 pounds of sand. Ensure the standpipe inside the tank remains centered while adding sand.
4. Once sand is added, attach the multi-port valve to the top of the tank, ensuring a secure and watertight seal. Use Teflon tape on all threaded fittings for a proper seal.

Figure 4: Filter tank capacity and design.

4.2 Pumpun kytkeminen

1. Place the pump unit on the filter base next to the tank.
2. Connect the pump's discharge port to the multi-port valve's 'PUMP' port using the provided short hose and clamps.
3. Varmista, että kaikki liitännät ovat tiukkoja vuotojen estämiseksi.

Figure 5: The pump unit and its specifications.

4.3 Liittäminen altaaseen

1. Connect one of the longer hoses from the multi-port valve's 'RETURN' port to your pool's return inlet.
2. Connect the other long hose from your pool's skimmer or suction inlet to the pump's suction port.
3. Secure all hose connections with the provided clamps. If your pool uses different hose sizes, you may need additional adapters (e.g., Hydrotools Item 71002 for Intex hose conversion).

5. Suodatinjärjestelmän käyttö

The 4-way multi-port valve allows for various operational modes.

5.1 Moniporttiventtiilin toiminnot

TÄRKEÄÄ: Always turn off the pump before changing the multi-port valve setting to prevent damage to the valve or system.

• SUODATTAMINEN: This is the standard operating mode for filtering pool water. Water flows from the pool, through the sand, and back to the pool.
• TAKASPESU: Used to clean the filter sand. Water flows in reverse through the sand, dislodging trapped debris, and is discharged out the waste port.
• HUUHTELU: Used after backwashing to settle the sand and flush any remaining debris from the valve before returning to filtration mode. Water is discharged out the waste port.
• TALVI: Used for winterizing the system. This position relieves pressure on the internal components of the valve.

Figure 6: The 4-Way Multi-Port Valve settings.

5.2 Järjestelmän käynnistäminen

1. Ensure all hoses are securely connected and the pool is filled to the appropriate level.
2. Set the multi-port valve to the 'BACKWASH' position.
3. Turn on the pump. Allow it to run for 1-2 minutes or until the water discharged from the waste port runs clear.
4. Sammuta pumppu.
5. Set the multi-port valve to the 'RINSE' position.
6. Turn on the pump. Allow it to run for 30-60 seconds.
7. Sammuta pumppu.
8. Set the multi-port valve to the 'FILTRATION' position.
9. Turn on the pump. The system is now operating in normal filtration mode.

5.3 Päivittäinen käyttö

Run the filter system for a minimum of 8-12 hours per day, or as needed, to maintain water clarity. Monitor the pressure gauge; an increase in pressure indicates the need for backwashing.

6. Huolto

Regular maintenance ensures the longevity and efficiency of your filter system.

6.1 Takaisinpesu

Backwash the filter when the pressure gauge reads 8-10 PSI above its clean operating pressure, or when pool water clarity decreases. Follow the 'Starting the System' steps for backwash and rinse procedures.

6.2 Hiekan vaihto

Filter sand typically lasts approximately 5 years, depending on water chemistry and backwashing frequency. Replace the sand when it no longer effectively filters the water, or when it becomes clumpy. Refer to the 'Preparing the Filter Tank' section for instructions on adding sand. As an alternative to sand, NEW 71015 Filter Balls can be used as an upgrade replacement media.

6.3 Talvittaminen

Before freezing temperatures, drain all water from the pump and filter tank. Disconnect hoses, remove the drain plug from the bottom of the tank, and set the multi-port valve to the 'WINTER' position. Store the pump and valve in a dry, protected area.

7. Vianmääritys

Tässä osiossa käsitellään yleisiä ongelmia, joita saatat kohdata.

8. Tekniset tiedot

Figure 7: Comparison table for various Hydrotools filter system models.

9. Takuutiedot

SWIMLINE HYDROTOOLS provides a 1-year guarantee against manufacturing defects for this sand filter system. This warranty covers defects in materials and workmanship under normal use and service.

10. Asiakastuki

For technical assistance, warranty claims, or general inquiries, please contact Swimline customer service. Contact information can typically be found on the manufacturer's website or on the product packaging. Please have your model number (71225) and purchase date available when contacting support.